Nidek Medical RT-5100 Скачать руководство пользователя страница 268

Страница: 268 / 306

250

MAINTENANCE

Cleaning Forehead Rest

6.2

Cleaning Forehead Rest

Clean the forehead rest before each refraction.

WARNING

• Be sure to secure the refractor head before removing or attaching the forehead rest.

If the refractor head is moved carelessly, it may bump against someone or something
and injury may occur.

Remove the forehead rest.

1) Tilt the forehead rest upward.

2) Pull it at an angle.

Wipe the forehead rest with a clean cloth.

For stubborn dirt, wash the forehead rest with dilute neu-
tral detergents.

• Be sure to wipe the forehead rest with a dry cloth.

It protects the forehead rest from rust.

Attach the forehead rest in the original position.

Insert the forehead rest at an angle.

6.3

Cleaning Face Shields

Clean the face shields before each refraction.

WARNING

• Be sure to secure the refractor head before removing or attaching the face shields.

If the refractor head is moved carelessly, it may bump against someone or something
and injury may occur.

Remove the face shields from the refractor head.

The face shields can be easily removed as they are fixed by magnets.

Wipe the face shields with a clean cloth.

For stubborn dirt, soak a cloth in a dilute neutral detergent, wring well, and wipe. Finally wipe
with a dry and soft cloth.

• Do not wipe the inner surface of the face shields with neutral detergents.

Doing so could make the inner surface becomes rust.

Attach the face shields in the original position.

161221687130 承認済

Uncontrolled copy when printed.

Содержание RT-5100



















































































































































































































































































































Результаты поиска

Содержание RT-5100

Отзывы:

Бренды по названию

Популярные бренды

Nidek Medical RT-5100, Руководство оператора

Результаты поиска

Содержание RT-5100

Отзывы:

Бренды по названию

Популярные бренды