Nidek Medical RT-5100 Скачать руководство пользователя страница 104

Страница: 104 / 306

OPERATING PROCEDURE

Power Adjustment (Final Fit)

2.7.4

Fine adjustment after auto adjustment (Semi-auto adjustment)

Adjust the Final Fit value calculated with the auto adjustment function precisely with the semi-auto
adjustment function.

• The Final Fit value calculated with the auto adjustment function is lower than an average

prescription. It avoids overcorrecting the patient. Be sure to adjust the value with the semi-
auto adjustment function.

After auto adjustment, ask the patient
whether he/she can see the chart clearly
and comfortably with the lenses of final pre-
scription 1 (Final 1).

Adjust the powers precisely.

Hard to see or undercorrect



Press

Overcorrect or uncomfortable



Press

The powers are adjusted and the data is
stored in [Final 2].

*19

Repeat Steps 1 and 2 until the patient sees the chart most clearly and comfortably.

The powers are adjusted and the data is stored in the order of [Final 3], [Final 4]

…

*20

2.7.5

Manual power adjustment

The powers can also be adjusted manually without the auto adjustment function.

Select the mode to be changed with

, or

and change each data with the dial.

For example:

1) Press

to present a chart with a patient’s desired visual acuity

2) Adjust the spherical and cylindrical powers to achieve the best possible visual acuity with

the most plus powers.

Manual adjustment is also available after auto adjustment.

*19.

See "8.1 Descriptions of Power Adjustment" (page 261) for adjusting the powers precisely with

when the auto

adjustment function is not used.

*20.

The RT-5100 stores up to five final prescription data. When the data whose prescription number is 6 or later is stored, the
prior data is deleted from Final 2. The Final 1 data (auto-adjustment) is not deleted.

161221687130 承認済

Uncontrolled copy when printed.

Содержание RT-5100



















































































































































































































































































































Результаты поиска

Содержание RT-5100

Отзывы:

Бренды по названию

Популярные бренды

Nidek Medical RT-5100, Руководство оператора

Результаты поиска

Содержание RT-5100

Отзывы:

Бренды по названию

Популярные бренды