Nidek Medical LE-9000DX Express страница 115 Скачать руководство пользователя

Страница: 115 / 153

8 - 14

4. Go back to the Layout screen.

Press

twice.

5. Repeat Steps 1 - 4 until the lens size just fits the frame.

8.7 Adjusting the Bevel Position

When the finished bevel of a lens is displaced from the designated position, adjust the bevel
position by changing the bevel constant.

1. Check the bevel position.

1) Read the traced data.

2) Process a lens of SPH: 0.0 D - +1.0 D.

3) Check the part where the edge is rather thin

to see if the point of the bevel is in the middle
of the edge.

If the bevel is leaning to either side, adjust
it by the following procedure.

2. Call up the MENU screen.

Press

㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖
㧖

㧹

㧱

㧺

㨁

㧖

㧖ޓޓޓޓޓޓ㧸㨑㨚㨓㨠㨔ޓ㧾㧦㧝㧠㧟㧚㧣㧤ޓ㧸㧦㧝㧠㧟㧚㧣㧢㧖
㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖

ޓޓޓ

ޓψޓ㧼㨞㨛㨏㨑㨟㨟ޓ㨏㨛㨡㨚㨠㨑㨞ޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓ

ޓޓޓ㨃㨔㨑㨑㨘ޓ㨐㨞㨑㨟㨟㨕㨚㨓ޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓ
ޓ

ޓޓޓ㧿㨕㨦㨑ޓ㨍㨐㨖㨡㨟㨠㨙㨑㨚㨠ޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓ
ޓ

ޓޓޓ㧮㨑㨢㨑㨘ޓ㨍㨐㨖㨡㨟㨠㨙㨑㨚㨠ޓޓޓޓޓޓޓޓޓޓޓޓޓޓ
ޓ

ޓޓޓ㧭㨄㧵㧿ޓ㨍㨐㨖㨡㨟㨠㨙㨑㨚㨠ޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓ
ޓ

ޓޓޓ㧼㧰ޓ㨍㨐㨖㨡㨟㨠㨙㨑㨚㨠ޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓ

Not good

Good

Not good

Содержание LE-9000DX Express


























































































































































Результаты поиска

Содержание LE-9000DX Express

Отзывы:

Похожие инструкции для LE-9000DX Express

Бренды по названию

Популярные бренды

Nidek Medical LE-9000DX Express, Руководство оператора

Результаты поиска

Содержание LE-9000DX Express

Отзывы:

Похожие инструкции для LE-9000DX Express

Бренды по названию

Популярные бренды