Nidec COMMANDER S100 Скачать руководство пользователя страница 72 | Manualshive

Страница: 72 / 118

background image

Getting started

72

Commander S100 User Guide

P2.24

Frequency Reference 4 Selector

Range:

0 to 9

Default:

0 (None)

These four parameters can be used to configure four individual references that the drive can use for speed control. For information on selecting
between these references see

Frequency Reference 1 to 4 Switch (

P2.20).

For inputs 0 - 4, the frequency references are transferred directly into the reference system. For inputs 5 - 9, the percentages selected are
converted to Hz using parameters

Minimum Frequency Limit

(P2.01) and

Maximum Frequency Limit

(P2.02).

Figure 7-6 Percent to Frequency scaling

If this parameter is set to 0 (None), the drive will run at the

Minimum Frequency Limit

(P2.01).

The value of these parameters can be set by

Frequency Reference Configuration

(P2.03).

Value Frequency Reference

Description

0

None

A fixed reference of 0 Hz

1

Preset 1

The frequency reference is defined by

Preset Frequency 1

(P2.16)

2

Preset 2

The frequency reference is defined by

Preset Frequency 2

(P2.17)

3

Preset 3

The frequency reference is defined by

Preset Frequency 3

(P2.18)

4

Preset 4

The frequency reference is defined by

Preset Frequency 4

(P2.19)

5

T2 Analog 1 %

The frequency reference is derived from

T2

Analog Percentage 1

(P1.15)

6

T4 Analog 2 %

The frequency reference is derived from

T4

Analog Percentage 2

(P1.16)

7

T15 Frequency %

The frequency reference is derived from

T15

Frequency Input Percentage

(P1.17)

8

Up/Down Percent

The frequency reference is derived from

Up/Down Percentage

(P1.18)

9

PID Percent

The frequency reference is derived from

PID Percentage

(P1.19)

NOTE

NOTE

«
...
70
71
72
73
74
...
»

Содержание COMMANDER S100























































































































Отзывы:

Нет отзывов

Похожие инструкции для COMMANDER S100

MINAS A6 Series

Бренд: Panasonic Страницы: 18

MINAS A6 Series

Бренд: Panasonic Страницы: 306

Бренд: Unitek Страницы: 50

Бренд: Graco Страницы: 4

ANT95LZS Series

Бренд: Aerotech Страницы: 48

Бренд: IBM Страницы: 20

Бренд: ABB Страницы: 20

Fortuna IV Series

Бренд: SunStar Страницы: 20

Бренд: Peaco Support Страницы: 244

Kollmorgen ACO5000

Бренд: ACOMEL Страницы: 22

Бренд: Berger Lahr Страницы: 45

Бренд: Leadshine Страницы: 22

Бренд: Lenze Страницы: 189

Бренд: ElectroCraft Страницы: 32

CACR-HR BAB Series

Бренд: YASKAWA Страницы: 293

Redi-Flo Series

Бренд: Grundfos Страницы: 16

Бренд: Grundfos Страницы: 140

Бренд: Gear Head Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды