Nidec COMMANDER S100 Скачать руководство пользователя страница 59

Страница: 59 / 118

Commander S100 User Guide

7.2.6 Menu 6 - IO configuration

Parameter

Range

Default

P6.01 T2 Analog Input 1 Type

0-10 V (0), Digital Input (1) 0-20 mA (2), 4-20 mA No Alarm (3), 4-20 mA Hold (4),

4-20 mA Stop (5), 4-20 mA Error (6)

4-20 mA (2)

P6.02 T4 Analog Input 2 Type

0-10 V (0)

P6.03 T6 Analog Output Type

0-10 V (0), 0-20 mA (1), 4-20 mA (2)

0-10 V (0)

P6.04 T11 Digital IO 1 Type

Digital Input (0), Digital Output (1), Frequency Output (2), PWM Output (3),

DO Inverted (4)

Digital Input (0)

P6.05 T15 Digital Input 5 Type

Digital Input (0), Frequency Input (1)

Digital Input (0)

P6.06 T6 Analog Output Function Select

None (0), Ramp Input (1), Ramp Output (2), Output Frequency (3),

Output Current (4), Torque Current (5), Output Voltage (6), DC Bus Voltage (7),

T2 Analog 1 % (8), T4 Analog 2 % (9),

T15 Frequency % (10), Output Power (11), Motor RPM (12), Percentage Load (13),

PID Percentage (14), PID Error (15), Motor Thermal % (16), Drive Thermal % (17)

Ramp Output (2)

P6.07 T6 Analog Output Scaling

0.000 to 40.000

1.000

P6.08 T41-T43 Relay Function Select

None (0), Drive Running (1), At Speed (2), At Zero (3), Under Voltage (4),

External Error (5), Drive Ready (6), Drive Healthy (7), Current Limit (8),

Reverse Running (9),Current Loss (10), Threshold Detect (11)

Drive Healthy (7)

P6.09 T11 Digital Output 1 Function Select

None (0)

P6.10

T11 Frequency/
PWM Output Function Select

None (0), Ramp Input (1), Ramp Output (2), Output Frequency (3),

Output Current (4), Torque Current (5), Output Voltage (6), DC Bus Voltage (7),

T2 Analog 1 % (8), T4 Analog 2 % (9),

T15 Frequency % (10), Output Power (11), Motor RPM (12), Percentage Load (13),

PID Percentage (14), PID Error (15), Motor Thermal % (16), Drive Thermal % (17)

None (0)

P6.11 T11 Frequency/PWM Output Scaling

0.000 to 40.000

1.000

P6.12 Negative Logic (NPN Sensor) Select

Off (0) or On (1)

Off (0)

P6.13 Run/Stop Configuration

Custom (0), Run F Run Reverse (1),

Run F Run Reverse (3 Wire) (2), Run + Reverse (3),

Run + Reverse (4), Run + Jog (5), Run F Run Reverse (6),

Run + Reverse (7), Keypad (8), Enable (9), Keypad Jog (10)

Run Forward

+ Run Reverse (1)

P6.14

T2 Analog Input 1 Digital Function
Select

None (0), Hardware Enable (1), Run Forward (2), Run Reverse (3), Run Permit (4),

Forward Limit Switch (5), Reverse Limit Switch (6),

Up/Down % Increase (7), Up/Down % Decrease (8), Up/Down % Reset (9),

Ref Switch Bit 0 (10), Ref Switch Bit 1 (11), Ramp Select (12),

PID Enable (13), External Error (14), Drive Reset (15), Run (16), Reverse (17),

Jog Forward (18), Jog Reverse (19), Fire Mode (20)

None (0)

P6.15

T4 Analog Input 2 Digital Function
Select

None (0)

P6.16 T11 Digital Input 1 Function Select

None (0)

P6.17 T12 Digital Input 2 Function Select

Hardware Enable (1)

P6.18 T13 Digital Input 3 Function Select

Run Forward (2)

P6.19 T14 Digital Input 4 Function Select

Run Reverse (3)

P6.20 T15 Digital Input 5 Function Select

Ref Switch Bit 0 (10)

P6.21 T2 Analog Input 1 Minimum Input

0.00 to 100.00 %

0.00 %

P6.22

T2 Analog Input 1 Percentage at
Minimum Input

±100.00 %

0.00 %

P6.23 T2 Analog Input 1 Maximum Input

0.00 to 100.00 %

100.00 %

P6.24

T2 Analog Input 1 Percentage at
Maximum Input

±100.00 %

100.00 %

P6.25 T4 Analog Input 2 Minimum Input

0.00 to 100.00 %

0.00 %

P6.26

T4 Analog Input 2 Percentage at
Minimum Input

±100.00 %

0.00 %

P6.27 T4 Analog Input 2 Maximum Input

0.00 to 100.00 %

100.00 %

P6.28

T4 Analog Input 2 Percentage at
Maximum Input

±100.00 %

100.00 %

P6.29 T15 Frequency Input Minimum Input

0.00 to 100.00 %

0.00 %

P6.30

T15 Frequency Input Percentage at
Minimum Input

±100.00 %

0.00 %

P6.31 T15 Frequency Input Maximum Input

0.00 to 100.00 %

100.00 %

P6.32

T15 Frequency Input Percentage at
Maximum Input

±100.00 %

100.00 %

Содержание COMMANDER S100























































































































Результаты поиска

Содержание COMMANDER S100

Отзывы:

Похожие инструкции для COMMANDER S100

Бренды по названию

Популярные бренды

Nidec COMMANDER S100, Руководство пользователя

Результаты поиска

Содержание COMMANDER S100

Отзывы:

Похожие инструкции для COMMANDER S100

Бренды по названию

Популярные бренды