Nidec COMMANDER S100 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 118

background image

installation

Drive parameters Communications

18

Commander S100 User Guide

3.3.1.3 Enclosure design and drive ambient temperature

Drive derating is required for operation in high ambient temperatures.
Totally enclosing the drive in either a sealed cabinet (no airflow) or in a well-ventilated cabinet makes a significant difference on drive cooling.
The chosen method affects the ambient temperature value (T

rate

) which should be used for any necessary derating to ensure sufficient cooling for the

whole of the drive.
The ambient temperature for the four different combinations is defined below:
1. Totally enclosed with no air flow (<2 m/s) over the drive T

rate

= T

int

+ 5 °C

2. Totally enclosed with air flow (>2 m/s) over the drive T

rate

= T

int

Where:

T

int

= Temperature inside the cabinet

T

rate

= Temperature used to select current rating from tables in section 10

Technical data

3.4 Drive fan operation

S100-01x13 and S100-01x23 drive are cooled by natural convection. All other drives are ventilated by an internally controlled fan that will turn on
when required to keep the drive cool.
Ensure the minimum clearances around the drive are maintained to allow air to flow freely.

3.5 Routine maintenance

Regular checks of the following should be carried out to ensure the drive reliability is maximized:

Table 3-5 Routine maintenance

Environment

Ambient temperature

Ensure the enclosure temperature remains at or below maximum specified.

Dust

Ensure the drive remains dust free. The lifetime of the fan is reduced in dusty environments. If the fibre filter

accessory is

used, ensure it remains clear and free of dust.

Moisture

Ensure the drive enclosure shows no signs of condensation. If moisture is discovered, an anti-condensation heater may
be required which must be switched off when the drive is running to prevent excess heating.

Enclosure

Enclosure particle filters Ensure filters are not blocked and that air is free to flow in and out of the enclosure.

Electrical

Screw connections

Ensure all screw terminals remain tight

Crimp terminals

Ensure all crimp terminals remain tight – check for any discoloration which could indicate overheating

Cables

Check all cables for signs of damage

Ground connections

Must be inspected and tested at appropriate intervals

«
...
16
17
18
19
20
...
»

Содержание COMMANDER S100























































































































Отзывы:

Нет отзывов

Похожие инструкции для COMMANDER S100

Бренд: GE Страницы: 86

PRO225LM Series

Бренд: Aerotech Страницы: 54

Бренд: SOLIDDRIVE Страницы: 2

Бренд: Sprint Electric Страницы: 8

Бренд: elero Страницы: 31

Бренд: Delixi Страницы: 33

Бренд: TOX PRESSOTECHNIK Страницы: 70

Бренд: Pro-dig Страницы: 26

Бренд: Leadshine Страницы: 13

RolloTron Pro Star Series

Бренд: RADEMACHER Страницы: 72

Rolltron PRO comfort

Бренд: RADEMACHER Страницы: 76

SERVOPACK Sigma 7S Series

Бренд: YASKAWA Страницы: 47

Бренд: LinMot Страницы: 91

Бренд: SEMIKRON Страницы: 37

USB 2.0 CD-RW/DVD-ROM Combo Drive

Бренд: IBM Страницы: 74

Бренд: Danfoss Страницы: 4

Бренд: Xinje Страницы: 194

SH-S203B - WriteMaster - DVD±RW

Бренд: Samsung Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды