TABLE A
– Pairings that occur automatically between buttons and commands, during memorisation of transmitters in Mode 1, in relation to the type of device connected to the
TT2Z K and the scheme used for this connection (1A, 1B or 1C).
Motor connection modes
Transmitter button
Memorised command
Motor connected with “Dry Contact”
(see scheme 1A)
s
Command:
UP
n
Command:
STOP
t
Command:
DOWN
Motor connected with 3 wires plus the earth wire
(“mechanical”-type motor)
(see scheme 1B)
s
Command:
UP
n
Command:
STOP
t
Command:
DOWN
Two independent “Switches”
(see scheme 1C)
s
Switching On / Off of
SWITCH 1
n
Switching off of
SWITCH 1
and of
SWITCH 2
t
Switching On / Off of
SWITCH 2
TABLE B
– Commands available during memorisation of a transmitter button, in
Mode 2.
Command
number
Number of but-
ton presses
Command that is memorised
No. 1
1
press
Open > Stop > Close > Stop > ...
No. 2
2
presses
Open > Stop > ...
No. 3
3
presses
Close > Stop > ...
No. 4
4
presses
Stop
4.1.2 - Mode 1 procedure, to memorise the FIRST
TRANSMITTER only (transmitter with PRG but-
ton)
01.
ON
If no transmitters
are memorised, TT2Z K
flashes 2 times
2
02.
PRG
7
sec
PRG
3
4.1.3 - Mode 1 procedure, to memorise an ADDITION
-
AL TRANSMITTER or a CLIMATE SENSOR (for
transmitters with PRG button)
01.
Wait at least 20 seconds from when the TT2Z K is
switched on before initiating this procedure
02.
OLD
PRG
5
sec
3
sec
2
2
PRG
03.
NEW
PRG
5
sec
2
PRG
04.
OLD
PRG
2
4.1.4 - Mode 1 procedure, to memorise an ADDITION
-
AL TRANSMITTER or a CLIMATE SENSOR (for
transmitters without PRG button)
01.
Wait at least 20 seconds from when the TT2Z K is
switched on before initiating this procedure
02.
NEW
10
sec
03.
OLD
x
3
04.
NEW
x
1
3
5.1.1 - Procedure for memorising a transmitter in
Mode 2 (for transmitters with PRG button)
01.
Wait at least 20 seconds from when the TT2Z K is
switched on before initiating this procedure
02.
OLD
PRG
5
sec
3
sec
2
2
PRG
03.
NEW
PRG
5
sec
2
PRG
04.
In Table B, select
the desired com
-
mand
OLD
x
N
10
sec
(feedback)
N
N
= number of button presses
(and feedback quantity) indicated
in Table B, next to the selected
command.
05.
NEW
?
5
sec
?
?
= a desired button, to be associated with the com
-
mand selected in Table B.
5.1.2 - Procedure for memorising a transmitter in
Mode 2 (for transmitters without PRG button)
01.
Wait at least 20 seconds from when the TT2Z K is
switched on before initiating this procedure
02.
NEW
10
sec
03.
OLD
x
1
4
04.
In Table B, select
the desired com
-
mand
OLD
x
N
N
= number of button presses indicated in Table B,
next to the selected command.
05.
NEW
?
5
sec
3
?
?
= a desired button, to be associated with the com
-
mand selected in Table B.
5.2.1 - Procedure for DELETING THE ENTIRE MEM-
ORY of the TT2Z K device, using a memorised
transmitter (with PRG button)
01.
PRG
x
1
2
02.
PRG
x
1
2
03.
PRG
x
1
3
04.
PRG
x
1
4
05.
PRG
x
1
5
5.2.2 - Procedure for DELETING THE ENTIRE MEMO-
RY of the TT2Z K device, using a NON-memo-
rised transmitter (with PRG button)
01.
OFF
(
TT2Z K
)
5
sec
ON
(
TT2Z K
)
02.
within 10 seconds:
NEW
5
sec
2
03.
OFF
(
TT2Z K
)
5
sec
ON
(
TT2Z K
)
04.
continue the procedure by completing all the
steps of the procedure indicated in Paragraph
5.2.1
User, installation and safety instructions
EN
Nice S.p.A.
Via Pezza Alta, 13
31046 Oderzo (TV), Italy
Radio receiver
Nice
TT2Z K
www.niceforyou.com
1(A)
- Connections of the outputs for DRY-CONTACT
It is possible to link to the dry contact output up to 8 motors maximum
1(B)
- Connections of the outputs for MECHANICAL MOTORS
(with 3 wires)
1(C)
- Connections of the outputs for 2 independent
SWITCHES
1
- White
2
- White-black
3
- White-orange
IS0487B00MM_26-10-2017
