Nice RUN1200HS, Инструкции и предупреждения по установке и использованию

Страница: 21 / 132

15
EN
TECHNICAL SPECIFICATIONS OF PRODUCT
WARNINGS: • All technical specifications stated in this section refer to an ambient temperature of 20°C (± 5°C). • Nice S.p.a. reserves the right to apply
modifications to products at any time when deemed necessary, maintaining the same intended use and functionality.
Model: RUN400HS - RUN400HS/V1 RUN1200HS - RUN1200HS/V1
Type Electromechanical gearmotor for automatic movement of sliding gates for industrial use complete with elec-
tronic control unit .
Pinion Number of teeth 18; Module 4 *
Maximum torque on start-up [cor-
responds to ability of generating the
force required to move the leaf]
12,3 Nm
(340 N)
28,4 Nm
(790 N)
Nominal torque [corresponds to the
ability of generating the force to main-
tain the leaf in movement]
5,6 Nm
(157 N)
8,2 Nm
(320 N)
Speed (no load)
42 m/min 22 m/min
Speed (at nominal torque) 32 m/min 19 m/min
Maximum frequency of operating
cycles (at nominal torque)
11 cycles/hour (264 cycles/day), for a gate of 15m
(equal to a cycle of 63%), (the control unit limits cycles
to the maximum number specified in tables 2 and 3)**
7-8 cycles/hour (365 cycles/day), for a gate of 15m
(equal to a cycle of 63%), (the control unit limits cycles
to the maximum number specified in tables 2 and 3)**
Maximum time of continuous
operation (at nominal torque)
40 minutes (the control unit limits continuous operation
to the maximum limits as specified in tables 2 and 3)***
60 minutes (the control unit limits continuous operation
to the maximum limits as specified in tables 2 and 3)***
Operating limits In general RUN is designed for the automation of gates with the weights and lengths as specified
Durability Estimated between 150.000 cycles and 450.000 cycles according to conditions specified in Table 4
Power: RUN 400HS - 1200HS
Versione V1
230V AC (+10% -15%) 50 Hz.
120Vac 50/60 Hz
Maximum power absorption on
start-up [corresponding to Amps]
510 W
(4,7 A)
550 W
(5,2 A)
Insulation class
1 (safety earthing required)
Flashing light output For 2 Flashing lights LUCYB (lamp 12V, 21W)
Gate open indicator output For 1 24V lamo of maximum 4W (output voltage may vary between -30 and +50% and can also control small
relays)
BLUEBUS output One output with a maximum load of 15 BlueBus units
STOP input For normally closed or normally open contacts, for 8.2 kΩ constant resistance; with self-recognition (any varia -
tion from the memorized status causes the “STOP” command)
Step-by-step input
For normally open contacts (contact closure generates S .S . command)
OPEN input For normally open contacts (contact closure generates OPEN command)
CLOSE input
For normally open contacts (contact closure generates the CLOSE command)
Radio connector SM connector for receivers SMXI; SMXIS or ONEXI
Radio ANTENNA input Input ANTENNA Radio 52Ω for cable type RG58 or similar
Programmable functions 8 ON-OFF type functions and 8 settable function (see tables 7 and 9)
Functions in self-learning mode Self-learning of devices connected to BlueBus output
Self-learning of “STOP” device type (contact NO, NC or 8,2KΩ resistance)
Self-learning of gate length and calculation of deceleration and partial opening points
Operating temperature
-20°C . . . 50°C
Protection rating IP 44
Dimensions and weight
400 x 255 h 390 mm; 24 .5kg
* 12 tooth modulus 6 pinion available as option .
** At 50°C and with a gate of 15 metres, the maximum operating frequency is 7 cycles/hour (equal to a cycle of 40%) .
*** At 50°C the maximum continuous operation time is 10 minutes .