manualshive.com logo in svg

Nibe S1255-12, Руководство по установке, Страница: 18 / 92

Поделиться
Скачать
Nibe S1255-12 Скачать руководство пользователя страница 18

General

All electrical equipment, except the outdoor sensors,
room sensors and the current sensors are ready connec-
ted at the factory.

• Electrical installation and wiring must be carried out

in accordance with the stipulations in force.

• Disconnect S1255 before insulation testing the house

wiring.

• If the building is equipped with an earth-fault breaker,

S1255 should be equipped with a separate one.

• S1255 must be installed via an isolator switch. The

cable area has to be dimensioned based on the fuse
rating used.

• If a miniature circuit breaker is used, this must have

motor characteristic "C" as a minimum. See section
"Technical specifications" for fuse size.

• To prevent interference, sensor cables to external

connections must not be laid close to high voltage
cables.

• The minimum area of communication and sensor

cables to external connections must be 0.5 mm² up
to 50 m, for example EKKX, LiYY or equivalent.

• Electrical wiring diagram for the heat pump, see sep-

arate Installer Manual.

• When cable routing in S1255, the cable grommets

(UB1 and UB2) must be used.

UB1

UB2

FC1

NOTE

Electrical installation and any servicing must
be carried out under the supervision of a quali-
fied electrician. Disconnect the current using
the circuit breaker before carrying out any ser-
vicing.

NOTE

If the supply cable is damaged, only NIBE, its
service representative or similar authorised
person may replace it to prevent any danger
and damage.

NOTE

Check the connections, main voltage and phase
voltage before the machine is started, to pre-
vent damage to the heat pump electronics.

NOTE

Do not start the system before filling up with
water. Components in the system could be
damaged.

MINIATURE CIRCUIT-BREAKER

The operating circuit in S1255 and some of its internal
components are fused internally by a miniature circuit
breaker (FC1).

S1255-6 3x400 V is not equipped with miniature circuit
breakers (FC1).

NIBE S1255

Chapter 5 | Electrical connections

18

5 Electrical connections

Содержание S1255-12





























































































Отзывы:

Нет отзывов