NI PXI-4204 Скачать руководство пользователя страница 9

Страница: 9 / 83

Chapter 1

About the NI PXI-4204

NI PXI-4204 User Manual

1-2

ni.com

What You Need to Get Started

To set up and use the NI PXI-4204, you need the following:

❑

Hardware

–

NI PXI-4204 device

–

Safety shell (provided)

–

COMBICON screw terminal connector (provided)

–

PXI or PXI/SCXI combination chassis

❑

Software

–

NI-DAQ 7.0 or later

–

One of the following:

•

LabVIEW

•

Measurement Studio

•

LabWindows

™

/CVI

™

❑

Documentation

–

NI PXI-4204 User Manual

–

Read Me First: Safety and Radio-Frequency Interference

–

DAQ Getting Started Guide

–

PXI or PXI/SCXI combination chassis user manual

–

Documentation for your software

❑

Tools

–

1/8 in. flathead screwdriver

You can download NI documents from

ni.com/manuals

National Instruments Documentation

The

NI PXI-4204 User Manual

is one piece of the documentation set for

your DAQ system. You could have any of several types of manuals,
depending on the hardware and software in your system. Use the
documentation you have as follows:

•

DAQ Getting Started Guide

—This document describes how to install

DAQ devices and the NI-DAQ driver software. Install NI-DAQ before
you install the SCXI module.

Содержание PXI-4204




















































































Результаты поиска

Содержание PXI-4204

Отзывы:

Бренды по названию

Популярные бренды

NI PXI-4204, Руководство пользователя

Результаты поиска

Содержание PXI-4204

Отзывы:

Бренды по названию

Популярные бренды