NexSens C-Boost Скачать руководство пользователя страница 1

 

 

1

 

 

 

QUICK START GUIDE 

C-Boost Cellular Signal Booster 

 

2091 Exchange Court 
Fairborn, Ohio 45324 
937-426-2703 

www.NexSens.com 

 

Figure 1: 

C-Boost

 

 

Overview 

The  NexSens  C-Boost  is  a  cellular  signal  booster 
for  use  in  conjunction  with  a  3100-iSIC  data 
logger.  It  provides  a  significant  boost  in  signal 
quality  to  allow  for  data  transmission  in  remote 
locations. 

What’s Included 

 

(1) C-Boost 

 

(1) 3 ft. Power Cable 

 

(1) Mounting Kit 

 

Common Accessories 

 

NexSens Micro-Loss RF Cable 

 

NexSens Low-Loss RF Cable 

Assembly 

The  main  components  of  the  C-Boost  are 
assembled  before  shipment,  but  a  few  final 
connections  must  be  made  prior  to  deployment. 
Quick instructions are provided in this guide. Visit 
the  online  Knowledge  Base  for  more  information 
(see 

Additional Information

 section). 

iSIC Power Cable Wiring 

The first step is to connect the power cable to the 
3100-iSIC. 

Before beginning, disconnect any external 

power sources such as solar panels or 

external batteries. 

Loosen  the  retained  screws  and  disconnect  the 
DB9  Serial  Cable  that  runs  from  below  the 
mounting plate to the connector in the middle of 
the terminal strips. 

 

Figure 2: 

Remove Serial Cable

 

Disconnect  the  fastons  from  the  battery 
terminals.  Remove  the  (2)  screws  from  the 
battery plate with a #3 Phillips head screwdriver. 
Remove the battery. 

 

Figure 3: 

Remove Battery

 

Содержание C-Boost

Страница 1: ...e shipment but a few final connections must be made prior to deployment Quick instructions are provided in this guide Visit the online Knowledge Base for more information see Additional Information section iSIC Power Cable Wiring The first step is to connect the power cable to the 3100 iSIC Before beginning disconnect any external power sources such as solar panels or external batteries Loosen the...

Страница 2: ...hes Figure 6 Install Sealcon Gland Fitting Feed the bare wire end of the provided C Boost power cable through the gland fitting from inside the box to outside Leave 6 in of cable inside the box with which to work Tighten the Sealcon using a 7 8 wrench Figure 7 Feed Power Cable Out of iSIC Remove the 2 Pin yellow MTA connector from the iSIC PCB and the 4 Pin Molex connector from the cellular modem ...

Страница 3: ...rt between the terminal strips and tighten down the two screws Figure 12 Connect Serial Cable C Boost Power Cable Wiring Next connect the power cable to the C Boost Feed the bare wire end of the provided C Boost power cable already fed through iSIC box through the C Boost POWER IN Sealcon from outside the box to inside Figure 13 Feed Power Cable into C Boost Connect the red wire to the V IN termin...

Страница 4: ...e RF cable from the iSIC Box to the C Boost s RF INPUT Figure 16 Connect RF Input Connect an N Style antenna or N Style RF cable with an attached antenna into the C Boost s RF OUTPUT Figure 17 Connect RF Output C Boost Specifications Power Requirements 8 0 to 36 0 VDC Power Consumption Idle 250mA Max 1A Signal Gain 15dB Cellular 850 15dB PCS 1900 Frequency Range 824 894 MHz 1850 1900 MHz Network C...

Отзывы: