Nexo PS Series Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 82

background image

PS

S

ERIES HARDWARE SETUP PROCEDURE

Page 31/82

7.2 General Description

PS10R2 and PS15R2 incorporate connecting plates (one on PS10R2 and one per side on PS15R2) on
which a comprehensive range of accessories can be mounted.

PS10R2 AND PS15R2 CONNECTING PLATES

There are two families of accessories:



fixed installation accessories, which are designed to be screwed on the connecting plates;



touring accessories, which can be installed or removed with quick connecting systems.

7.2.1 WARNINGS ON PS SERIES ACCESSORIES

WARNING 1T

All PS Accessories are specifically rated in agreement with structural computations.
Never use other accessories when installing PS Series cabinets cabinets than the ones
provided by NEXO: NEXO will decline responsibility over the entire PS Series accessory
range if any component is purchased from different supplier.

WARNING 2

All PS Series accessories have been designed so that cabinets are installed as single
standalone speakers.
PS Series assemblies as shown in figure below are UNSAFE and STRICTLY PROHIBITED.

NO

Oblong holes for Touring Applications Accessories

Tapped holes for Fixed Installation Accessories

«
...
29
30
31
32
33
...
»

Содержание PS Series



















































































Отзывы:

Нет отзывов

Похожие инструкции для PS Series

Бренд: Samson Страницы: 92

Бренд: Jafar Страницы: 10

Бренд: Rane Страницы: 2

Бренд: Mackie Страницы: 16

Бренд: TANDBERG Страницы: 47

Бренд: Maclaren Страницы: 43

Бренд: Lawler Страницы: 5

GRAVIMETRIC AUGER FEEDER MGF-ST

Бренд: Maguire Products Страницы: 47

Бренд: Magtrol Страницы: 160

SHERPA MONOBLOC B0812

Бренд: Olimpia splendid Страницы: 44

Бренд: Olimpia splendid Страницы: 44

Бренд: Olimpia splendid Страницы: 16

Digiplex DGP-848

Бренд: Paradox Страницы: 20

Бренд: Patron Страницы: 17

Spartan-3A DSP FPGA Series

Бренд: Xilinx Страницы: 140

Бренд: Mitsubishi Страницы: 16

Бренд: SOMFY Страницы: 4

Бренд: Bettis Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды