Nexcom NDiS B533 Скачать руководство пользователя | Manualshive

Страница: 10 / 68

background image

Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved.

x

NDiS B533 User Manual

Preface

Technical Support and Assistance

1. For the most updated information of NEXCOM products, visit NEXCOM’s

website at www.nexcom.com.

2. For technical issues that require contacting our technical support team or

sales representative, please have the following information ready before
calling:
– Product name and serial number
– Detailed information of the peripheral devices
– Detailed information of the installed software (operating system,

version, application software, etc.)

– A complete description of the problem
– The exact wordings of the error messages

Warning!
1. Handling the unit: carry the unit with both hands and handle it with care.

2. Maintenance: to keep the unit clean, use only approved cleaning products

or clean with a dry cloth.

3. CompactFlash: Turn off the unit’s power before inserting or removing a

CompactFlash storage card.

Conventions Used in this Manual

Warning:
Information about certain situations, which if not observed,
can cause personal injury. This will prevent injury to yourself
when performing a task.

CAUTION!

CAUTION!

CAUTION!

Caution:
Information to avoid damaging components or losing data.

Note:
Provides additional information to complete a task easily.

«
...
8
9
10
11
12
...
»

Содержание NDiS B533





































































Отзывы:

Нет отзывов

Похожие инструкции для NDiS B533

Бренд: Gardner Bender Страницы: 8

Бренд: NARIKA Страницы: 2

Бренд: Bayer HealthCare Страницы: 56

ClimateMaster Tranquility 22 Digital TZ Series

Бренд: Nibe Страницы: 72

Бренд: Giebel Страницы: 9

Бренд: R.V.R. Elettronica Страницы: 44

MobilSwitch-Micro-C

Бренд: SeaSoft Страницы: 7

7x7 NG Plus 4 Series

Бренд: Monosem Страницы: 94

Бренд: SCHUNK Страницы: 36

Бренд: Beckhoff Страницы: 51

Бренд: Hitachi Страницы: 8

SuperDrive 75 Series

Бренд: Hitachi Страницы: 2

Бренд: Hitachi Страницы: 49

Бренд: Hitachi Страницы: 129

Бренд: Hitachi Страницы: 34

Бренд: Hitachi Страницы: 44

Бренд: Hitachi Страницы: 161

Бренд: Hitachi Страницы: 313

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды