Newport New Focus 8703 Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 41

Newport New Focus 8703 Скачать руководство пользователя страница 39

Safety Precautions

29

•

There are no user-replaceable fuses in this equipment. The user must
ensure that appropriate current-limiting protection is provided by the
external DC power source.

•

To avoid explosion, do not operate this equipment in an explosive
atmosphere.

•

Qualified service personnel should perform safety checks after any
service.

5.2.2

General Cautions

Observe these cautions when operating this equipment:

•

If this equipment is used in a manner not specified in this manual, the
protection provided by this equipment may be impaired.

•

Do not block ventilation openings.

•

Use only the specified replacement parts.

•

Follow precautions for static sensitive devices when handling this
equipment.

•

This product should only be powered as described in the manual.

•

There are no user-serviceable parts inside the Model 8712 Picomotor
Drive Module.

5.2.3

Summary of Warnings and Cautions

The following general warning and cautions are applicable to this instrument:

WARNING

The Picomotor Driver is incomplete in constructional features
and is considered only to be a component for the purposes of
regulatory compliance. It is “equipment for building in;” a
suitable enclosure must be provided so that the unit is not user
accessible when incorporated into the final product.

WARNING

The Model 8712 Picomotor Driver internally generates non-SELV
voltages and shall be installed with the enclosure, mounting,
spacings, and marking requirements of the end-use application.

«
...
37
38
39
40
41
»

Содержание New Focus 8703










































Отзывы:

Нет отзывов