IMPORTANT NOTICE
All wiring should be carried out by a competent person or a qualified electrician and should be fitted to IEE 17th Edition Wiring regulations
BS7671:2008. The circuit should be isolated before carrying out any work. Failure to adhere to the instructions will invalidate the warranty.
Instructions
Newlec Helpline: 0800 783 6909
RPM 491
PRODUCT RANGE
NEWLEC DALI OCCUPANCY DETECTOR
PART NUMBER
NL5701DALI
FEATURES
Presence and Absence Detection Options
Automatic Daylight Harvesting
Settable Timing Modes
Basic Luminaire setup without expensive commissioning
tools
Broadcast and Group Functions
Dual Mode Remote Control
Room & Corridor Options
Manual Lux Level and Sensitivity Control
Coloured Feedback LEDs
Walk Test
Can control LED and fluorescent DALI luminaires
A
Absence Control Lines
A
Absence Control Lines
DA
DALI Bus line
DA
DALI Bus line
NEWLEC DALI OCCUPANCY DETECTOR WIRING CONNECTIONS
NEWLEC DALI OCCUPANCY DETECTOR INSTRUCTIONS MUST BE READ IN CONJUNCTION WITH REMOTE CONTROL IN-
STRUCTIONS IN ORDER TO ENABLE ALL FEATURES OF THE OCCUPANCY DETECTOR
This flush mounted ceiling mount Newlec DALI Occupancy Detector has full DALI flexibility and is the intelligent sensor element of
the Newlec DALI network system. It can automatically address the lighting ballasts without the need for expensive controllers. The
Occupancy Detector is switched on by the detection of moving body heat within a specified range. When this moving body heat is no
longer detected the unit will dim down the luminaires and eventually switch off. It will also automatically harvest available daylight to
maximise energy savings. With the remote it is possible to set dimming time delays and Room and Corridor options. There are also
helpful coloured feedback LEDs to make programming easier.
MAINS POWER SHOULD NEVER BE CONNECTED TO ANY TERMINAL OF THE DALI OCCUPANCY DETECTOR
The DALI connections are made to the DA DA bus lines. There is no polarity but it is advisable and good practice to keep wiring
colours to the same connections for consistency.
Absence detection on the Newlec DALI network system can easily be achieved with the addition of a standard 1 gang 1 way switch. If
2 way and intermediate switches are required these can also be connected in to the terminals. To turn this DALI Occupancy Detector
from a presence detector to an absence detector simply connect an ordinary on/off switch to the A and A Absence Control lines and
the Occupancy Detector can be switched between presence and absence mode as desired.
CAREFUL POSITIONING OF THE OCCUPANCY DETECTOR IS ESSENTIAL TO MAINTAIN OPTIMUM DETECTION PERFORMANCE.
Occupancy Detector detection pattern
2.4 METRES
Instruction Data
374-‐CMPIRDALI
Elkay easyDALi PIR
18v d.c. 250ma for use with Power Supply Unit
(374-‐PSU)
Features
Presence and Absence Detection Options
Automatic Daylight Harvesting
Settable Timing Modes
Basic Luminaire setup without expensive commissioning tools
Broadcast and Group Functions
Remote Control
Room & Corridor Options
Manual Lux Level and Sensitivity Control
Coloured Feedback LEDs
Dual Mode Walk Test
Can control LED and fluorescent DALI luminaires
Elkay easyDALi PIR Instructions must be read in conjunction
with Remote Control Instructions in order to enable all
features of the PIR.
This flush mounted ceiling mount Elkay easyDALi PIR has full DALI
flexibility and is the intelligent sensor element of the Elkay easyDALI
system. It can automatically address the lighting ballasts without the
need for expensive controllers. The PIR is switched on by the
detection of moving infra-‐red heat within a specified range. When
this moving infra-‐red heat is no longer detected the unit will dim
down the load and eventually switch off. It will also automatically
harvest available daylight to maximise energy savings.
With the remote it is possible to set dimming time delays and Room
and Corridor options. There are also helpful coloured feedback LEDs
to make programming easier.
Elkay easyDALI PIR wiring connections
A
Absence Control Lines
A
Absence Control Lines
DA
DALI Bus line
DA
DALI Bus line
Mains power should never be connected to any terminal of
the easyDALi PIR.
The DALI connections are made into DA DA bus lines. There is
no polarity but it is advisable and good practice to keep
wiring colours to the same connections for consistency.
To turn this easyDALi PIR from a Presence detector to an
absence detector simply connect an ordinary on/off switch to
the A and A Absence Control lines and the PIR will know
automatically that it is in Absence mode.
Absence detection on the Elkay easy DALI system can easily
be achieved with the addition of a standard 1 gang 1 way
switch. If 2 way and intermediate switches are required these
can also be connected in to the terminals.
CAREFUL POSITIONING OF THE PIR IS ESSENTIAL TO
MAINTAIN OPTIMUM DETECTION PERFORMANCE.
d
A A DA DA
