Newland NLS-HR32 Series Скачать руководство пользователя страница 30

Страница: 30 / 300

Power On, Power Off, Reboot

Power on the scanner

Hold down the trigger on the scanner until it beeps.

Note: When using the scanner for the first time or after scanning the

Battery Off

barcode in Chapter 3, you MUST insert

the scanner in a powered cradle to exit battery protection mode before turning it on.

Power off the scanner

Method 1:

When in the Level scan mode, the scanner will automatically power off after 5 minutes of inactivity.

Method 2:

Scan the

Power Off

Scanner

barcode in Chapter 3.

Reboot the scanner

If the scanner stops responding to input or runs abnormally, use a straightened paperclip to press and hold the Reset

button on the bottom of the scanner to reboot it.

Maintenance



The scan window should be kept clean.



Do not scratch the scan window.



Use soft brush to remove the stain from the scan window.



Use the soft cloth to clean the window, such as eyeglass cleaning cloth.



Do not spray any liquid on the scan window.



Do not use any detergent to clean other parts of the device except for water.

The warranty DOES NOT cover damages caused by inappropriate care and maintenance.

Содержание NLS-HR32 Series













































































































































































































































































































Результаты поиска

Содержание NLS-HR32 Series

Отзывы:

Похожие инструкции для NLS-HR32 Series

Бренды по названию

Популярные бренды

Newland NLS-HR32 Series, Руководство пользователя

Результаты поиска

Содержание NLS-HR32 Series

Отзывы:

Похожие инструкции для NLS-HR32 Series

Бренды по названию

Популярные бренды