Newland NLS-EM20-EX Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 187

background image

Startup settings

Image stabilization timeout (sensing mode)

In the sensing mode, when the scanner stops reading the code, it will enter a process of re-adapting to the changes in the reading environment (image), and it will enter the sensing state after the image stabilization times out

Wait for the barcode to appear. By modifying the image stabilization timeout, the time to adapt to the environment can be adjusted. The setting range is 1 To 3000 Milliseconds, default is 200 millisecond.

[Image stabilization timeout (sensing mode)]

Delay setting

Reread delay

•

Turn on:

If the scanner reads a bar code and reads the bar code for the second consecutive time within the reread delay time, the bar code read for the second time will be ignored and will not

Output.

•

shut down:

The reread delay is invalid. The scanner can continuously read the same barcode at any time.

Default: Reread delay is off.

* *

【Open】

* * 【shut down】

13

Exit settings

«
...
21
22
23
24
25
...
»

Содержание NLS-EM20-EX




























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NLS-EM20-EX

Universal 3 in 1 Reader/Writer

Бренд: Dazzle Страницы: 47

Бренд: Salto Страницы: 6

Бренд: Avery Dennison Страницы: 103

Бренд: Xcellon Страницы: 8

Бренд: Onyx International Страницы: 38

Бренд: Jamex Страницы: 15

3-in-1 Card Reader/Writer TS0MFLRD

Бренд: Transcend Страницы: 17

Бренд: Unitech Страницы: 2

Бренд: Bematech Страницы: 500

Бренд: SICK Страницы: 77

Lector63x Flex C-mount

Бренд: SICK Страницы: 98

Бренд: Opticon Страницы: 25

Бренд: Approx Страницы: 92

Бренд: U-Line Страницы: 18

Бренд: GE Security Страницы: 18

Бренд: 2connect Страницы: 63

Бренд: RIOTEC Страницы: 3

Бренд: Kantech Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды