Newland NLS-BS80 Скачать руководство пользователя страница 31

Страница: 31 / 264

USB Mode

When the scanner is in the USB mode, you can select a desired protocol by scanning the appropriate
barcode below.

USB HID-KBW (default)

USB COM Port Emulation

There are two types of data transmission via USB: Asynchronous transmission and Batch transmission.

(1)

Asynchronous transmission (default):

When the scanner is not connected to PC via USB cable,

scanned data will be stored in the flash memory. When the scanner is connected to PC via USB cable,
scanned data will be sent to PC directly.

(2)

Batch transmission:

Scanned data will be stored in the flash memory no matter whether the scanner

is connected to PC or not.

You can sync the data from the flash memory to your PC via USB by following the procedure described
below.

Step 1: Download CDC-Virtual COM Driver from Newland website at

www.newlandaidc.com

and Install it

on your PC.

Step 2: Connect the scanner to your PC with USB cable. The scanner beeps when the connection
between them is established.

Step 3: Open Notepad or Office Word on your PC and make sure that your cursor is always positioned in
it. Hold down the Function button on the scanner for 3 seconds or scan the

Transmit Stored Data

barcode to start data transmission from the flash memory to your PC. The scanner beeps when the
transmission is completed.

Содержание NLS-BS80









































































































































































































































































Результаты поиска

Содержание NLS-BS80

Отзывы:

Похожие инструкции для NLS-BS80

Бренды по названию

Популярные бренды

Newland NLS-BS80, Руководство пользователя

Результаты поиска

Содержание NLS-BS80

Отзывы:

Похожие инструкции для NLS-BS80

Бренды по названию

Популярные бренды