Newland HR3260-CS Скачать руководство пользователя страница 42

Страница: 42 / 165

【

Enter Setup

】

【

Exit Setup

】

Sensitivity

Sensitivity specifies the degree of acuteness of the scanner’s response to changes in ambient
illumination. The higher the sensitivity, the lower requirement in illumination change to trigger the scanner.

You can select an appropriate degree of sensitivity that fits the ambient environment.

【

Medium Sensitivity

】

【

Low Sensitivity

】

【

High Sensitivity

】

【

Enhanced Sensitivity

】

If the above four options fail to meet your needs, you may program the threshold value of illumination

change.

Illumination changes that reaches or surpasses the predefined threshold value will cause the scanner to

start a decode session. The lower the threshold value, the greater the sensitivity of the scanner. The

default threshold value is 2.

【

Threshold Value of Illumination Change (1~20)

】

Set the threshold value of illumination change to 4:

1. Scan the

Enter Setup

barcode.

2. Scan the

Threshold Value of Illumination Change

barcode.

Scan the numeric barcode “4”. (See the

Digit Barcodes

Appendix

)

4. Scan the

Save

barcode. (See the

Save/Cancel Barcodes

Appendix

)

5. Scan the

Exit Setup

barcode.

Содержание HR3260-CS






































































































































































Результаты поиска

Содержание HR3260-CS

Отзывы:

Похожие инструкции для HR3260-CS

Бренды по названию

Популярные бренды

Newland HR3260-CS, Руководство пользователя

Результаты поиска

Содержание HR3260-CS

Отзывы:

Похожие инструкции для HR3260-CS

Бренды по названию

Популярные бренды