New lift FST Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 174

background image

3 FST-Controller user interface

3.1 LC-Display and messages

FST_HB.EN04/03

29

LEARN START FAILURE!

The started learn drive has been aborted due to the car not moving even with
pre-selection active.

DRV-TEST STARTED!

A drive test has been triggered.

DRV-TEST FINISHED!

The drive test has been completed successfully.

CAR NUISANCE DETECT!

The car nuisance protection function has triggered. See

MAIN MENU -

Config - Anti Nuisance

NOT IN THE ZONE!

The started learn drive can not be completed because the car is not in the door
zone. Check function of Zone B signal and settings in

MAIN MENU -

Positioning - Increm.Pos. - ZoneB-Level

. Check setting of

jumper JMP7 on the FST board.

NOT IN FLOOR-0!

The started learn drive can not be completed because the car is not on the
lowest floor.

NOT FROM END FLOOR!

The car is at an end floor. The triggered end switch test cannot be started from
this floor.

ONLY FROM END FLOOR!

The triggered drive test can only be started from an end floor.

PC-CARD REMOVED!

The inserted PC-Card has been removed from slot X8.

PC-CARD FLASH TYPE??

The flash type of the inserted PC-Card is unkown. The PC-Card cannot be
used.

PC-CARD EMPTY!

The inserted PC-Card has been cleared successfully.

PC-CARD LOW BATTERY!

The battery voltage of the inserted PC-Card is too low. Change battery!

PC-CARD OK!

The inserted PC-Card has been recognized by the controller and can be used.

PC-CARD TYPE????!

The inserted PC-Card has not been recognized by the controller and cannot be
used.

Checking Update File

The software is updated. The inserted PC-Card is checked for update files.

RECORDING RE_START!

An already started recording has been restarted.

RECORDING STOPPED!

Recording has been stopped.

RECORDING NEW START!

A new recording is started.

SUPERVISOR LEVEL!

The supervisor level is accessed with a master password. It enables setting
hidden parameters.

FILE NOT FOUND!

The software update has been aborted. The inserted PC-Card does not contain
update files.

UPDATE FILE FOUND

The file required for the software update has been found on the PC-Card. The
software is updated.

UPDATE COMPLETE!

The software update of the LON module has been completed.

WAITING TO RESET...

Automatic RESET after changing basic parameters (e.g.

Drive type

). This

may take a few seconds.

EXCESSIVE SLIPPAGE!!

During the last drive of the learn drive hysteresis of the connected solenoid
switches CT, CB and Zone B has been detected (only when using incremental
positioning). If a value greater than 10mm is measured this message is
displayed. Hysteresis is limited to 10mm automatically. See “ZoneB–Hysters”
on page 135.

DOOR-NUDGING!

Nudging (forced closure) of the car door is activated. Photocell and reversing
contacts are ignored. See

MAIN MENU - Doors - Doors

Selective - Photocell

and

MAIN MENU - Doors - Doors

Selective - Nudge Time

.

Display

Description

«
...
29
30
31
32
33
...
»

Содержание FST















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для FST

Бренд: Bang & Olufsen Страницы: 80

Бренд: Bang & Olufsen Страницы: 13

Бренд: CALEFFI Страницы: 2

Бренд: CALEFFI Страницы: 12

Бренд: Caliber Страницы: 6

Бренд: Lawler Страницы: 4

Бренд: Hama Страницы: 46

Бренд: Galcon Страницы: 35

Бренд: ECKELMANN Страницы: 178

Бренд: echoflex Страницы: 8

Бренд: H3C Страницы: 17

Бренд: H3C Страницы: 32

BT300 BurnerTronic

Бренд: Lamtec Страницы: 48

Бренд: VAT Страницы: 39

Бренд: Samson Страницы: 124

Бренд: Samson Страницы: 86

Бренд: VAC Страницы: 5

Бренд: Bartlett Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды