New lift FST Скачать руководство пользователя страница 144 | Manualshive

Страница: 144 / 174

background image

1 Menu tree
1.7 MAIN MENUE – System

142

FST_HB.EN04/03

Recorder –

Filter Setting

RIO Traffic

Enable event channel “RIO Traffic” for recording. See “Event
Channels” on page 143.

ON
OFF

Recorder –

Stop-when-full

Determines if recordings stops when the PC-Card is full.
Otherwise recording continues at the start of the card (endless
loop).

YES
NO

Update FST

Update the FST software with a PC-Card.

³

YES
NO

Update GST

Update the GST software with a PC-Card.

³

YES
NO

Update LON-Modules

Update all connected LON-Modules if a new software version
is available on the PC-Card.

³

YES
NO

Config --> Backup

Create a backup copy of the current FST configuration for
storage in an internal buffer.

³

YES
NO

Config <-- Backup

Load the FST configuration from the internal buffer as current
FST configuration. All parameters will be overwritten. Only
activate this parameter after consulting NEW LIFT!

³

YES
NO

PC-Card Tools –

Config --> Card

Save current FST configuration on PC-Card.

³

YES
NO

PC-Card Tools –

Config <-- Card

Load the FST configuration from the PC-Card as current FST
configuration. All parameters will be overwritten. Only activate
this parameter after consulting NEW LIFT!

³

YES
NO

PC-Card Tools –

S/Ware --> Card

Save current FST software on PC-Card.

³

YES
NO

PC-Card Tools –

Clear Card

Delete everything on the PC-Card.

³

YES
NO

Panel Test

Special function to test landing and in-car panels (see System
description – Panel Test).

FST Reset!

RESET the FST-Controller.

³

YES
NO

Menu item

Description

Setting range

«
...
142
143
144
145
146
...
»

Содержание FST















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для FST

DELTAFLUX MT100

Бренд: PIETRO FIORENTINI Страницы: 16

Бренд: Parasound Страницы: 72

Бренд: Jafar Страницы: 15

Бренд: Eaton Страницы: 166

Бренд: DAVIS Страницы: 8

7000-2 - Escalade RAID Controller

Бренд: 3Ware Страницы: 2

Origami 4M-006-01

Бренд: 4 Moms Страницы: 28

Бренд: Abus Страницы: 12

Бренд: Federal Signal Corporation Страницы: 79

Бренд: Federal Signal Corporation Страницы: 32

Бренд: halstrup-walcher Страницы: 39

GRAVIMETRIC AUGER FEEDER MGF-ST

Бренд: Maguire Products Страницы: 47

Бренд: Magtrol Страницы: 160

Бренд: Tamas Страницы: 12

Бренд: We Care Solar Страницы: 46

Бренд: Watts Страницы: 4

OneFlow OFTWH-R

Бренд: Watts Страницы: 8

Бренд: Full Gauge Controls Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды