New lift FST-2XTs Скачать руководство пользователя страница 23

Страница: 23 / 50

Replacing FST-2s with FST-2XTs

Functiontests

ManualforreplacingFST-2swithFST-2XTs

5.4

Function tests

► Switch on the MAIN SWITCH (Q1) and the fuse (F4).

► Wait until the FST-2XTs software has completely started.

► Switch on the circuit breaker for car and shaft light and, if applicable, the UPS.

► Activate the emergency call control system or the emergency horn.

► Switch on the AUXILIARY MODE CONTROL (AUX).

Check the lift ID-number

► Simultaneously press buttons





and check the lift ID number.

If the lift ID number is displayed correctly:

No further steps necessary.

If the lift ID number is not displayed correctly:

Perform data transfer again.

If the lift ID number is not displayed correctly after repeating data transfer:

Upload the necessary ID data using the FST editor program or

Perform complete commissioning according to the commissioning manual

See MIA FST-2XT/XTs.

Position check

► Use buttons



�

on the display to set position value P = XXXXX.

► Turn the AUXILIARY MODE switch to UP and observe the set value.

The position value must increase.

► In the same way, turn the AUXILIARY MODE switch to DOWN and observe the set value.

The position value must decrease.
If the position values correspond to the selected direction of movement:

No further steps necessary.

If the position values do not correspond to the selected direction of car movement:

Press button



to change to the

main menu

Use buttons

�

to navigate to the

Positioning/Global/Direction

submenu and confirm each with



By confirming selection

Left/Right

, you can change the direction of rotation.

Repeat the position check.

Содержание FST-2XTs



















































Результаты поиска

Содержание FST-2XTs

Отзывы:

Похожие инструкции для FST-2XTs

Бренды по названию

Популярные бренды

New lift FST-2XTs, Руководство пользователя

Результаты поиска

Содержание FST-2XTs

Отзывы:

Похожие инструкции для FST-2XTs

Бренды по названию

Популярные бренды