New Holland WE150B страница 17 Скачать руководство пользователя | Manualshive

Страница: 17 / 51

background image

INTRODUCTION

Hoses and tubes

Always replace hoses and tubes if the cone end or the
end connections on the hose are damaged.

When installing a new hose, loosely connect each end
and make sure the hose takes up the correct position be-
fore tightening the connections. Clamps should be tight-
ened sufficiently to hold the hose without crushing and to
prevent chafing.

After hose replacement to a moving component, check
that the hose does not foul by moving the component
through the complete range of travel. Be sure any hose
which has been installed is not kinked or twisted.

Hose connections which are damaged, dented, crushed
or leaking, restrict oil flow and the productivity of the com-
ponents being served. Connectors which show signs of
movement from the original position have failed and will
ultimately separate completely.

A hose with a frayed outer sheath will allow the water pen-
etration. Concealed corrosion of the wire reinforcement
will subsequently occur along the hose length with resul-
tant hose failure.

Ballooning of the hose indicates an internal leakage due to
structural failure. This condition rapidly deteriorates and
total hose failure soon occurs.

Kinked, crushed, stretched or deformed hoses generally
suffer internal structural damage which can result in oil
restriction, a reduction in the speed of operation and ulti-
mate hose failure.

Free-moving, unsupported hoses must never be allowed
to touch each other or related working surfaces. This
causes chafing which reduces hose life.

TULI12WEX2014AA

11

O-rings

Replace O-rings, seal rings and gaskets whenever they
are disassembled.

Never mix new and old seals or O-rings, regardless of
condition. Always lubricate new seal rings and O-rings
with hydraulic oil before installation to relevant seats.

This will prevent the O-rings from rolling over and twisting
during mounting which will jeopardize sealing.

47500165A 31/01/2013

10

«
...
15
16
17
18
19
...
»

Содержание WE150B




















































Отзывы:

Нет отзывов

Похожие инструкции для WE150B

Бренд: Howard Страницы: 17

Бренд: SANY Страницы: 208

Бренд: Meec tools Страницы: 19

Бренд: Yuchai Страницы: 157

Бренд: IHI Страницы: 103

Бренд: Toro Страницы: 72

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды