New Holland W190D Скачать руководство пользователя

Страница: 26 / 61

INTRODUCTION

Consumables

Capacities and specifications

Engine

Type of oil

NEW HOLLAND AMBRA UNITEK 10W-40

Technical specifications

SAE 10W-40

API CJ-4

NEW HOLLAND CONSTRUCTION specifications

MAT3521

Type of oil

NEW HOLLAND AMBRA UNITEK SSL 0W-40

(cold weather)

Technical specifications

SAE 0W-40
API CJ-4

NEW HOLLAND CONSTRUCTION specifications

MAT3521

Capacity (with filter change)

13.25 L

(

14 US qt

)

Total capacity in system

15.1 L

(

16 US qt

)

Cooling system

Type of coolant

NEW HOLLAND AMBRA ACTIFULL™ OT
EXTENDED LIFE COOLANT

NEW HOLLAND CONSTRUCTION specifications

MAT3624

System capacity

30 L

(

32 US qt

)

Fuel system

System capacity

288 L

(

76 US gal

)

Hydraulic system

Type of fluid

NEW HOLLAND AMBRA HYDROSYSTEM 46 HV

Technical specifications

ISO VG-46

NEW HOLLAND CONSTRUCTION specifications

MAT3509

Total system capacity

178 L

(

47 US gal

)

Reservoir capacity

90.8 L

(

24 US gal

)

Transmission

Type of oil

NEW HOLLAND AMBRA MULTI G 134™ HYDRAULIC
TRANSMISSION OIL

Technical specifications

SAE 10W - 30
API GL-4
ISO VG-32/46

NEW HOLLAND CONSTRUCTION specifications

MAT 3525

Service capacity - with filter change

34.1 L

(

36 US qt

)

Axles

Type of oil

NEW HOLLAND AMBRA TRX 80W-140

Technical specifications

SAE 80W-140
API GL-4

NEW HOLLAND CONSTRUCTION specifications

MAT 3510

Front axle (Standard and Heavy Duty)

40 L

(

42.3 US qt

)

Rear axle (Standard and Heavy Duty)

40 L

(

42.3 US qt

)

DEF/A

LUE

Technical specifications

ISO 22241-1

NEW HOLLAND CONSTRUCTION specifications

ES-BS001

Total capacity (*)

37.1 L

(

39.2 US qt

)

Grease fittings, as required

NEW HOLLAND AMBRA GR 75 MD

NEW HOLLAND CONSTRUCTION specifications

MAT3550

Grade C

NOTICE:

(*) some liters always remain in the

DEF/A

LUE

reservoir. This allows for correct functioning of the wheel

loader components. DO NOT overfill the

DEF/A

LUE

tank. The tank is full when the

DEF/A

LUE

fluid level in

the tank reaches the bottom of the fill neck. Adequate air volume must be present in the top of the tank for proper
functionality of the after treatment system.

48144035_EN 03/07/2017

Содержание W190D






























































Результаты поиска

Содержание W190D

Отзывы:

Похожие инструкции для W190D

Бренды по названию

Популярные бренды

New Holland W190D, Руководство по обслуживанию

Результаты поиска

Содержание W190D

Отзывы:

Похожие инструкции для W190D

Бренды по названию

Популярные бренды