New Holland E175C Скачать руководство пользователя страница 31

Страница: 31 / 51

INTRODUCTION

Basic instructions - Precaution for disassembly and assembly

Preparations for disassembly

• Thoroughly wash the machine before bringing it into the shop. Bringing a dirty machine into the shop may cause

machine components to be contaminated during disassembling/assembling, resulting in damage to machine com-
ponents, as well as decreased efficiency in service work.

• Be sure to thoroughly understand all disassembling/assembling procedures beforehand, to help avoid incorrect

disassembling of components as well as personal injury.

• Check and record the items listed below to prevent problems from occurring in the future.

1. The machine model, machine serial number, and hour meter reading.

2. Reason for disassembly (symptoms, failed parts, and causes).

3. Clogging of filters and oil, water or air leaks, if any.

4. Capacities and condition of lubricants.

5. Loose or damaged parts.

• Prepare the necessary tools to be used and the area for disassembling work.

• Wear appropriate clothing, safety shoes, safety helmet, goggles, and clothes with long sleeves.

• Confirm the position of first-aid kit and fire extinguisher, and also where to make contact for emergency measure

and ambulance to prepare for accidents and fire.

• Attach “Don’t operate” tag to control lever, and begin a meeting before starting the work.

Disassembling and assembling hydraulic equipment

• Before removing pipes, release the pressure of hydraulic oil tank, or open the cover on the return side to tank, and

take out the filter.

• Drain the oil in the removed pipes into pan to prevent the oil from spilling on the ground.

• Pipes with plugs or caps to prevent oil leaking, entry of dust, etc.

• Clean the outside surface of equipment, etc. before disassembling, and drain hydraulic oil and gear oil before

putting them on working.

Disassembling hydraulic equipment

• Since performance and function of hydraulic equipment after disassembly and assembly results in immunity from

responsibility on the manufacture’s side, disassembly, assembly and modification without permission are strictly
prohibited.

• If it is unavoidably necessary to disassemble and modify, it should be carried out by experts or personnel qualified

through service training.

• Make match mark on parts for reassembling.

• Before disassembling, read disassembling Instruction in advance, and determine if the disassembly and assembly

are permitted or not.

• For parts which are required to use jig and tools, don’t fail to use the specified jig and tools.

• For parts which can not be removed in the specified procedure, never force removal. First check for the cause.

• Inspecting parts. Measure the wear of parts and clearance, and record the measured values.

• If an abnormality is detected, repair or replace the parts.

• The removed parts should be put in order and tagged so as to install on proper places without confusion.

• For common parts, pay attention to the quantity and places.

Reassembling hydraulic equipment

• During the parts cleaning, ventilate the room.

47494131A 11/03/2013

Содержание E175C




















































Результаты поиска

Содержание E175C

Отзывы:

Похожие инструкции для E175C

Бренды по названию

Популярные бренды

New Holland E175C, Руководство по обслуживанию

Результаты поиска

Содержание E175C

Отзывы:

Похожие инструкции для E175C

Бренды по названию

Популярные бренды