New Holland B80B Скачать руководство пользователя

Страница: 36 / 51

Engine - Engine and crankcase

Engine - Remove

Prior operation:

Refer to

Basic instructions

Prior operation:

Refer to

Hood - Remove (90.100)

Prior operation:

Refer to

Radiator - Remove (10.400)

Prior operation:

Refer to

Exhaust manifold - Remove (10.254)

NOTE:

Put identification tags on all disconnected hoses

and wires. Close all disconnected hoses and fittings with
caps and plugs immediately.

NOTE:

The images in this procedure may be different from

your machine and are for reference only.

ATTENTION:

Allow the engine to reach normal tempera-

ture before performing any service or maintenance proce-
dure. Wear safety gloves and goggles for protection from
hot components and fluids or severe burns could result.

1. Drain engine oil by loosening the drain nut. Collect the

oil in a clean container, cap it and keep it aside in a
clean place.

2. Disconnect the fuel return and inlet lines

(1)

from the

mud filter

(4)

and cap them immediately.

Loosen the mounting bolts

(2)

and remove the assem-

bly

(3)

from the machine.

PTIL13TLB0953AB

3. Remove the exhaust pipe

(1)

of the turbocharger and

cap it.

PTIL13TLB0956AB

48143704 20/04/2017

10.1 [10.001] / 3

Содержание B80B




















































Результаты поиска

Содержание B80B

Отзывы:

Похожие инструкции для B80B

Бренды по названию

Популярные бренды

New Holland B80B, Руководство по обслуживанию

Результаты поиска

Содержание B80B

Отзывы:

Похожие инструкции для B80B

Бренды по названию

Популярные бренды