New England Arbors Trellis Pergola Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 21

New England Arbors Trellis Pergola Скачать руководство пользователя страница 16

16

STEP NINE

Biltmore Pergola

Place the pergola at the desired location and pound the supplied

mounting stakes with a hammer into the ground.

If mounting onto concrete or decking material, please consult

mounting options at the end of this instruction.

Pergola Mounting

1

1

2

This pergola has been designed to be easy to install and anchor to

the ground. If you are in a high wind location and require more

stability, please see the next page on how to install the posts into

the ground.

Fasten the pergola with 1” hex head tek screws provided at the

locations shown. You will need to pre-drill the holes through the

mounting plates first using the drill bit provided.

2

Important step

: ensure that your ground is level. This can be

accomplished by a combination of building up the ground with

soil and/or digging as necessary.

x 24

Note: A hex driver
or wrench will be
needed to fasten
these screws.

5/16” or 8mm

«
...
14
15
16
17
18
...
»

Содержание Trellis Pergola






















Отзывы:

Нет отзывов