background image

Check Box for These Contents (1 Box) 

In the event of missing or defective parts please call our customer service dept. at 

1 800 282 9346

 

(Mon. to Fri. 8:00 AM to 4:00 PM EST)

.

    

    1.  

Posts 

(2)

 

4”x 4“ x 54” - 10126

    2.  

Top Rails 

(2)

 

2“ x 3.5” x 44.5“ - 10103

    3.  

Bottom Rails 

(2)

 

2“ x 3.5” x 43.5“ - 10104

    4. 

 Pickets 

(4)

 

.875“ x 3” x 29.25“ - 10105

         Pickets 

(2)

 

.875“ x 3” x 30“ - 10107

         Pickets 

(2)

 

.875“ x 3” x 31.5“ - 10108

         Pickets 

(2)

 

.875“ x 3” x 32.75“ - 10109

         Pickets 

(2)

 

.875“ x 3” x 34.25“ - 10110

         Pickets 

(2)

 

.875“ x 3” x 36.25“ - 10111

         Pickets 

(2) .875“ x 3” x 38.25“ - 10112

         Pickets 

(2)

 

.875“ x 3” x 41“ - 10113

    5. 

 External Post Caps

 (2) 4” x 4” - 10735-1

    6. 

 Post Trim Caps

 (2) 4” x 4” - 10737-1 

    7. 

 Base Moldings

 (2) 5” x 5” - BM20022

    8. 

 Rail Mount Brackets 

(8) 2” x 3.5” - 10045

        

 Hardware Kit (Includes):

    

9.  

Self-tapping stainless Screws

 (32) .625” - 20016 

 

10. 

 

Rail end spacers

 (2) 2“ x 3.5” x .5” - 10217  

 11. 

Tube of vinyl cement

 (1) - 20000

        

Tools You Will Need

    •  Cordless Drill with #2 Phillips bit
    •  Tape measure
    •  Pencil
    •  Level
    •  Shovel
    •  Two bags of pre-mix concrete (optional)

General Information

    • 

 Read Instructions through carefully before beginning assembly.

    •  When handling components, place on a non-abrasive surface

         (i.e. shipping box) 

to avoid scratching. 

    •  We recommend an area approx 5’x 5’ for unobstructed handling.

Cottage Picket Wings

Please read through before starting assembly.

ASSEMBLY INSTRUCTIONS

1

1

V2.4/091916

9

Not to Scale

2

11

3

4

8

5

6

7

10

5"

5"

8"

39"

49"

18.75"

44"

www.newenglandarbors.com

Содержание Cottage Picket Wings






Отзывы: