NEW BRUNSWICK SCIENTIFIC C2 Classic Скачать руководство пользователя

Страница: 32 / 41

Figure 9: Belt Removal

DRIVE

PULLEY

BEARING HOUSING

PULLEY

9. Grab the belt from underneath the

SUBPLATFORM

, pull it forward and over one

corner of the

SUBPLATFORM

. Repeat for the other corner until the belt clears the

SUBPLATFORM

, but is constrained by the

LOWER MOVER PLATE

10. Slide the belt to one of the unattached sides of the

LOWER MOVER PLATE

and pull it

through the opening.

11. Slide the belt to the other side of the

LOWER MOVER PLATE

, pull it through the

opening, and remove it from the unit.

12. Install the replacement belt in similar fashion.

13. Reattach the

UPPER FLEXURES

to the

LOWER MOVER PLATE

14. Reattach the

COVER

to the frame and secure.

15. Reinstall the

MOVER PLATES

and secure.

M1244-0051

C2 Classic Platform Shaker

User’s Guide

Содержание C2 Classic










































Результаты поиска

Содержание C2 Classic

Отзывы:

Похожие инструкции для C2 Classic

Бренды по названию

Популярные бренды

NEW BRUNSWICK SCIENTIFIC C2 Classic, Руководство по эксплуатации

Результаты поиска

Содержание C2 Classic

Отзывы:

Похожие инструкции для C2 Classic

Бренды по названию

Популярные бренды