Nevir NVR-4802-6P-12CD, Руководство пользователя

Страница: 35 / 41

43 42
15
14
EN 50242: this program is the test cycle
The information for comparability test in accordance with EN50242,as follows:
- Capacity: 12 settings
- Position of upper basket: Low position
- Rinse aid setting: 5 (or 4 for four setting dispenser)
6. Starting a Washing Programme
Wash cycle table
Program
Cycle Selection
Information Description
of Cycle
Detergent
Pre/main
Running
Time
(min)
Energy
(kWh)
Water
(L)
For the heaviest soiled loads,
such as pots, pans, casserole
dishes and dishes that have
been sitting with dried food
on them for a while.
For normally soiled loads,
such as pots, plates, glasses
and lightly soiled pans.
standard daily cycle.
For lightly soiled loads, such
as plates, glasses, bowls and
lightly soiled pans.
Light wash cycle to be used
for more delicate items which
are sensitive to high
temperatures.(Run cycle
immediately after use)
A shorter wash for lightly
soiled loads that do not
need drying.
To rinse dishes that you
plan to wash later that day
Pre-wash1
Pre-wash2
Main wash(60 )
Hot rinse
Drying
Pre-wash1
Pre-wash2
Main wash(50 )
Hot rinse
Drying
Pre-wash
Main wash
(45 )
Hot rinse
Drying
Pre-wash
Main wash
(40 )
Hot rinse
Drying
Main wash(40 )
Hot rinse
Pre-wash
5/25
5/25
5/20
5/20
15
168
153
123
126
37
8
14
14
11
11
7
4
1.30
1.03
0.85
0.80
0.50
0.01
WARNING!
It is dangerous to open the door when washing, because the hot water may scald you.
Switch Off the Dishwasher
The digital display appears "--" and the buzzer rings 6 times, only in this case the programme has
ended.
1.Switch off the dishwasher by pressing the on/off button.
2.Turn off the water tap!
Open the door carefully. Hot steam may escape when the door is opened!
Hot dishes are sensitive to knocks. The dishes should therefore be allowed to cool down around
15 minutes before removing from the appliance.
Open the dishwasher's door, leave it ajar and wait a few minutes before removing the dishes. In
this way they will be cooler and the drying will be improved.
Unloading the dishwasher
It is normal that the dishwasher is wet inside.
Empty the lower basket first and then the upper one. This will avoid water dripping from the upper
basket onto the dishes in the lower one.
Switching on
1. Open the tap, if it is closed.
2. Close the door.
3. Make sure the spray arms are not obstructed.
4. Switch the dishwasher on using the " Start/Pause " button.
Select a programme
Choose your programme according to the type of load and how dirty it is.
The different programmes and their uses are described in the programme chart
later on in this
booklet. Use the programme selector to select the expected programme .
Change the Programme.
Premise: A cycle that is underway can only be modified if it has only been running for a short time.
Otherwise, the detergent may have already been released, and the appliance may have already
drained the wash water. If this is the case, the detergent dispenser must be refilled (see the section
entitled " Fill in the Detergent " ).
1:Press the on/off button or reset button( dishwasher with reset button) 3 seconds to cancel the
programme.
2:Turn on it again and restart a new washing cycle (see the section entitled "Starting a wash cycle. . . " )
or press programme button (dishwasher with reset button) to change the programme.
NOTE: If you open the door when the washing cycle underway, the appliance will pause and emit
warning signals, the digital display show E1 and flash. When you close the door, the machine will
keep on working after 10 seconds.
" " " "
" "
" "
Forget to Add Dish
A forgotten dish can be added any time before the detergent cup opens.
1 Open the door a little to stop the washing.
2 After the spray arms stop working, you can open the door completely.
3 Add forgotten dishes.
4 Close the door, the dishwasher will work after ten seconds.
Starting a wash cycle...
Draw out the lower and upper basket, load the dishes and
1. push them back. It is recommended to load the lower basket first, then the upper one (see the
section entitled "Loading the Dishwasher"). Pour in the detergent (see the section entitled "Salt,
Detergent and Rinse Aid").
2. Insert the plug into the socket. The power supply is 220-240V AC 50 Hz, the specification of the
socket is 12 A 250 VAC.50 Hz.
Make sure that the water supply is turned on to full pressure. Close the door, press the on/off
button, press the "program." button to select a desired "Wash cycle". (See the section entitled "Wash
Turning on the Appliance
Intensive
Crystal
Light
Pre-Rinse
Rapid
Eco
(*E 50242)
Programme) (Standard
Cycle Table".)
With a little force to ensure the door is properly closed.
NOTE:
A click could be heard when the door is closed perfectly.
When the washing is over, you can shut off the switch by pressing on/off button.
N