background image

 

 

10 

Note: 

Please do not disassemble the device unless it is required to replace the batteries.   

Do not touch the waterproof gasket, LED indicator light, function keys when replacing the batteries. Please use suitable 

screwdriver to tighten the screws (if using an electric screwdriver, it is recommended to set the torque as 4kgf) to ensure the 

device is impermeable. 

 

Note on battery use: 

Because the passivation of the ER battery electrode surface is an inherent characteristic of lithium thionyl chloride batteries, 

before using the  ER14505 3.6V 2400mAh lithium thionyl chloride battery, the user can use a 33 ohm resistor to activate the 

battery for 1 minute to actively eliminate the battery hysteresis. 

7. Important Maintenance Instruction 

Kindly pay attention to the following in order to achieve the best maintenance of the product: 

 

  Keep the device dry. Rain, moisture, or any liquid, might contain minerals and thus corrode   

electronic circuits. If the device gets wet, please dry it completely. 

  Do not use or store the device in dusty or dirty environment. It might damage its detachable parts   

and electronic components. 

  Do not store the device under excessive heat condition. High temperature can shorten the life of   

electronic devices, destroy batteries, and deform or melt some plastic parts. 

  Do not store the device in places that are too cold. Otherwise, when the temperature rises to   

normal temperature, moisture will form inside, which will destroy the board. 

  Do not throw, knock or shake the device. Rough handling of equipment can destroy internal   

circuit boards and delicate structures. 

  Do not clean the device with strong chemicals, detergents or strong detergents. 

  Do not apply the device with paint. Smudges might block in the device and affect the operation. 

  Do not throw the battery into the fire, or the battery will explode. Damaged batteries may also   

explode. 

 

All of the above applies to your device, battery and accessories. If any device is not working properly, please take it to the nearest 

authorized service facility for repair. 

 

Содержание R718LB












Отзывы: