background image

 

 

the batteries to power off the device.       

7. Low Voltage Alarming 

The  operating  voltage  threshold  is  3.2V.  If  the  voltage  is  lower  than  3.2V,  R718F2  will  send  a 
low-power warning message to the LoRa network. 

8. Installation 

Connect the reed switch sensor of the connection module to the door edge, and align the magnet           
with  the  door  along  the  corresponding  door  frame  position.  Make  sure  the  reed  sensor  is  not 
triggered when the door is closed. 
 
This product comes with waterproof function. When using it, the back of it can be adsorbed on the 
iron surface, or the two ends can be fixed to the wall with screws. 
Note: To install the battery, use a screwdriver or similar tool to assist in opening the battery cover. 
 

9. Important Maintenance Instruction 

Your  device  is  a  product  of  superior  design  and  craftsmanship  and  should  be  used  with  care.  The 
following suggestions will help you use the warranty service effectively. 
• Keep the equipment dry. Rain, moisture, and various liquids or moisture may contain minerals that 
can corrode electronic circuits. In case the device is wet, please dry it completely. 
•  Do  not  use  or  store  in  dusty  or  dirty  areas.  This  can  damage  its  detachable  parts  and  electronic 
components. 
• Do not store in excessive heat. High temperatures can shorten the life of electronic devices, destroy 
batteries, and deform or melt some plastic parts. 
•  Do  not  store  in  a  cold  place.  Otherwise,  when  the  temperature  rises  to  normal  temperature, 
moisture will form inside, which will destroy the board. 
• Do not throw, knock or shake the device. Rough handling of equipment can destroy internal circuit 
boards and delicate structures. 
• Do not wash with strong chemicals, detergents or strong detergents. 
• Do not apply with paint. Smudges can block debris in detachable parts and affect normal operation. 
• Do not throw the battery into a fire to prevent the battery from exploding. Damaged batteries may 
also explode. 
All of the above suggestions apply equally to  your device, battery and accessories. If any device is 
not working properly. 
Please take it to the nearest authorized service facility for repair.

 

 

Содержание R718F2








Отзывы: