NETGEAR Nighthawk X4S R7800 Скачать руководство пользователя страница 57

Страница: 57 / 160

Your changes are saved.

Delete a Reserved IP Address Entry

To delete a reserved address entry:

Launch a web browser from a computer or wireless device that is connected to the network.

Type http://www.routerlogin.net .

A login window opens.

Enter the router user name and password.

The user name is admin. The default password is password. The user name and password are case-sensitive.

The BASIC Home page displays.

Select ADVANCED > Setup > LAN Setup.

The LAN Setup page displays.

Select the radio button next to the reserved address.

Click the Delete button.

The address is removed.

Use the WPS Wizard for WiFi Connections

The WPS Wizard helps you add a wireless computer or device to your WiFi network without typing the WiFi password.

To use the WPS Wizard:

Launch a web browser from a computer or wireless device that is connected to the network.

Type http://www.routerlogin.net .

A login window opens.

Enter the router user name and password.

The user name is admin. The default password is password. The user name and password are case-sensitive.

The BASIC Home page displays.

Select ADVANCED > WPS Wizard.

A note explaining WPS displays.

Click the Next button.

Network Settings

Nighthawk X4S AC2600 Smart WiFi Router

Содержание Nighthawk X4S R7800

































































































































































Результаты поиска

Содержание Nighthawk X4S R7800

Отзывы:

Похожие инструкции для Nighthawk X4S R7800

Бренды по названию

Популярные бренды

NETGEAR Nighthawk X4S R7800, Руководство пользователя

Результаты поиска

Содержание Nighthawk X4S R7800

Отзывы:

Похожие инструкции для Nighthawk X4S R7800

Бренды по названию

Популярные бренды