NETGEAR Nighthawk AX6 AX4300 Скачать руководство пользователя | Manualshive

Страница: 158 / 162

background image

Test the path from a Windows-based computer to a remote
device

To test the path from a Windows-based computer to a remote device:

1. From the Windows toolbar, click the Start button and select Run.

2. In the Windows Run window, type

ping -n 10

<IP address>

where

<IP address>

is the IP address of a remote device such as your ISP DNS server.

If the path is functioning correctly, messages display that are similar to those shown
in Test the LAN path to your router on page 157.

3. If you do not receive replies, check the following:

•

Check to see that IP address of your router is listed as the default gateway for
your computer. If DHCP assigns the IP configuration of your computers, this
information is not visible in your computer Network Control Panel. Verify that the
IP address of the router is listed as the default gateway.

•

Check to see that the network address of your computer (the portion of the IP
address specified by the subnet mask) is different from the network address of
the remote device.

•

Check to see that your cable or DSL modem is connected and functioning.

•

If your ISP assigned a host name to your computer, enter that host name as the
account name on the Internet Setup page.

•

Your ISP might be rejecting the Ethernet MAC addresses of all but one of your
computers.

Many broadband ISPs restrict access by allowing traffic only from the MAC address
of your broadband modem. Some ISPs additionally restrict access to the MAC address
of a single computer connected to that modem. If your ISP does this, configure your
router to “clone” or “spoof” the MAC address from the authorized computer.

User Manual

158

Troubleshooting

Nighthawk AX6 6-Stream AX5400 WiFi Router

«
...
156
157
158
159
160
...
»

Содержание Nighthawk AX6 AX4300



































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Nighthawk AX6 AX4300

Бренд: Panasonic Страницы: 24

Бренд: Panasonic Страницы: 2

BB-HCM381A - Network Camera

Бренд: Panasonic Страницы: 28

BB-HCM381A - Network Camera

Бренд: Panasonic Страницы: 2

Netlink FRX4000

Бренд: Cabletron Systems Страницы: 8

Бренд: Cabletron Systems Страницы: 4

MMAC-Plus 9F106-02

Бренд: Cabletron Systems Страницы: 7

Бренд: IBM Страницы: 32

Бренд: NETGEAR Страницы: 169

Protege PRT-PX16-PCB

Бренд: ICT Страницы: 34

ADSL 2/2+ VPN Firewall Router ADE-4300A/B

Бренд: Planet Страницы: 132

StorageWorks AIT 35GB AutoLoader

Бренд: Compaq Страницы: 4

PoleVault System A/V Source Inputs

Бренд: Extron electronics Страницы: 4

Бренд: E-TOP Страницы: 24

Бренд: Intellinet Страницы: 12

Бренд: Caton Страницы: 18

Бренд: Techroutes Страницы: 20

DL-DVI-Vision-IP Series

Бренд: G&D Страницы: 228

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды