manualshive.com logo in svg

NETGEAR DGN2200M - Wireless-N 300 Router, Руководство пользователя, Страница: 16 / 95

Поделиться
Скачать
NETGEAR DGN2200M - Wireless-N 300 Router Скачать руководство пользователя страница 16

Internet Configuration

16

N300 Wireless ADSL2+ Modem Router DGN2200Mv2 

ADSL Settings

For information about how to install ADSL filters, see the 

Setup Manual

.

NETGEAR recommends that you use the Setup Wizard to automatically detect and configure 
your ADSL settings. This usually works fine. However, if you have technical experience and 
are sure of the multiplexing method and virtual circuit number for the virtual path identifier 
(VPI) and virtual channel identifier (VCI), you can specify those settings here.

Note:  

Use the Setup Wizard to select the correct country to optimize 

detection of the ADSL settings.

NAT (Network Address 
Translation)

NAT automatically assigns private IP addresses (10.0.0.x) to devices on 
your LAN.

• 

Enable

. Usually NAT is enabled.

• 

Disable

. This disables NAT, but leaves the firewall active. Disable NAT 

only if you are sure that you do not require it. When NAT is disabled, only 
standard routing is performed by this router. Classical routing lets you 
directly manage the IP addresses that the wireless modem router uses. 
Classical routing should be selected only by experienced users.

1

• Advanced users can also bridge or disable the firewall.

Router MAC Address

Your computer’s local address is its unique address on your network. This is 
also referred to as the computer’s MAC (Media Access Control) address. 

• 

Use Default MAC Address

. This is the usual setting.

• 

Use Computer MAC address. 

If your ISP requires MAC authentication, 

you can use this setting to disguise the wireless modem router’s MAC 
address with the computer’s own MAC address. 

• 

Use This MAC Address

. If your ISP requires MAC authentication, you 

can manually type the MAC address for a different computer. The format 
for the MAC address is XX:XX:XX:XX:XX:XX. 

1. Disabling NAT reboots the wireless modem router and resets its configuration settings to the factory defaults. 
Disable NAT only if you plan to install the wireless modem router in a setting where you will be manually 
administering the IP address space on the LAN side of the router.

Settings

Description

Содержание DGN2200M - Wireless-N 300 Router
































































































Отзывы:

Нет отзывов