Industrial Ethernet to Fiber Media Convertor
Hardware Installation Guide
Version 1.2
Updated in April, 2015
Introduction
Inside the Package
Product Description
EF23 Series
Tel: 886-3-5508137
Fax: 886-3-5508131
www.atop.com.tw
P/N:89900403G
EF23 Series
10/100 Base-T(X) to 100Base-FX Media Converters
EF23G Series
1000Base-T to 1000Base-X Media Converters
Atop Technologies, Inc.
Thank you for choosing the Atop Industrial DIN-Rail Ethernet to Fiber Media
Converter. The EF23/EF23G Series provide industrial grade media conver-
sion between 10/100Base-T(X) and 100Base-FX (SC connector); and
1000Base-T and 1000BASE-X(SC connector or SFP).
This Guide covers Five product models:
EF23 Series
■
EF23-1-Fm-SC-2:
Fast Ethernet 10/100Base-T(X) to 100Base-FX Media Converter with
extended operating temperature.
Include 1 10/100Mbps RJ45 and 1 100Mbps Multi-mode Optical Fiber.
■
EF23-1-Fs-SC-30:
Fast Ethernet 10/100Base-T(X) to 100Base-FX Media Converter with
extended operating temperature.
Include 1 10/100Mbps RJ45 and 1 100Mbps Single-mode Optical Fiber.
EF23G Series
■
EF23-1G-1Fm-SC-550M:
Gigabit Ethernet 1000Base-T to 1000Base-X Media Converter with extended
operating temperature.
Include 1 1000Mbps RJ45 and 1 1000M Multi-mode Optical Fiber.
■
EF23-1G-1Fs-SC-10:
Gigabit Ethernet 1000Base-T to 1000Base-X Media Converter with extended
operating temperature.
Include 1 1000Mbps RJ45 and 1 1000Mbps Single-mode Optical Fiber.
■
EF23-1G-1SFP:
Gigabit Ethernet 1000Base-T to 1000Base-X Media Converter with extended
operating temperature.
Include 1 1000Mbps RJ45 and 1 1000Mbps SFP slot.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received; including interference
that may cause undesired operation.
■
Main Product
■
Atop EF23/EF23G industrial Ethernet Media Converter x1
■
Standard accessories
■
3-pin Terminal Block (2ESDVM-03P) x1
Atop P/N: 50706701G
■ RJ-45 Port Plugs x1
Atop P/N: 3990012G
■ Hardware Installation Guide (Warranty card is include) x1
Atop P/N: 89900403G
Optional Accessories
■
3-pin Terminal Block(2ESDVM-03P )
Atop P/N: 50706701G
■
Adapter : 3-pin Terminal block (5.08 mm) power adaptor,
100-240VAC input, 1.25A @ 12VDC output, US plug
Atop P/N: 70100000000027G
■
Adapter : 3-pin Terminal block (5.08 mm) power adaptor,
100-240VAC input, 1.25A @ 12VDC output, EU plug
Atop P/N: 70100000000028G
Hardware Installation
■
Electrical
Step 1:
Unpack the Media Converter, check
to make sure no external damages.
Step 2:
Connect the power adapter/supply (6-48VDC);
It is normal to see the PWR indicator on.
Step 3:
Connect the RJ-45 port to your Ethernet device.
Step 4:
Connect the fiber optical port from EF23 to
another EF23 or a switch. Make sure you
connect the cable’s Tx to Rx and Rx to Tx.
At this point, you should see the
FX_LINK/ACT LED indicator on.
Step 5:
Now check to make sure your Ethernet device can access the
network.
■
Mechanical
Media Converters are equipped with a DIN-Rail bracket attached onto the
rear panel. Follow the steps below to fasten the Media Converter to the
DIN-Rail.
Step 1:
Tilt the unit slightly backwards.
Step 2:
Fit the unit over top the DIN-Rail.
Step 3:
Push downwards and against the DIN-Rail for locking.
Step 4:
Check that the unit is locked into position.
1. TX Port: 10/100 Base-T(X)
2. Green: PWR SPD LED
3. Green: TX_LINK/ACT TX_FDX/COL LED
4. Green: FX_LINK/ACT FX_FDX/COL LED
5. FX Port: 100 Base-FX (SC Connector)
EF23G Series
1. TX Port: 1000 Base-T
2. Green: ACT TX_LINK
3. Green: PWR
FX_FDX/COL LED
4. FX Port: 1000 Base-X
(SC Connector or SFP Solt)
EF23 Series DIP Switch Definition
* SPEED is only for TX
* LFP: Link Fault Pass-through
* This table only applies to EF23 series
WARNING:
Disconnect the power and allow to cool 5 minutes before touching.
Never install or work on electrical or cabling during periods of
lighting activity. Never connect or disconnect power when hazard-
ous gases are present.
Caution:
CLASS 1 LASER PRODUCT. Do not stare into the laser!
DIP Switch
1
2
3
4
5
Mode
TX_DUPLEX_MODE
FX_DUPLEX_MODE
SPEED_MODE
LFP
Auto Negotiation
OFF
Full(default)
Full(default)
100M(default)
Disable(default)
Enable(default)
ON
Half
Half
10M
Enable
Disable
