manualshive.com logo in svg

NetApp StorageGRID Webscale 10.4, Руководство по установке и обслуживанию

Поделиться
Скачать
NetApp StorageGRID Webscale 10.4 Скачать руководство пользователя страница 22

Task

Description

Install enclosure in rack

Install the DE1600 enclosure or DE6600 enclosure in the rack.

If you are lifting the DE6600 enclosure by hand, attach the four
enclosure handles for easier lifting. You can remove these
handles later.

Install drives in drive drawer

For the SG5660 model, install the drives in the DE6600
enclosure drive drawer.

 

 

Related information

E2700 Controller-Drive Tray and Related Drive Trays Installation Guide
E5600 Controller-Drive Tray and Related Drive Trays Installation Guide

Installing the E5600SG controller in the enclosure

If the E5600SG controller is not installed when you receive the enclosure, you might need to install it
into Slot B.

About this task

You can skip this procedure if the E5600SG controller is already installed in the enclosure.

Steps

1.  Remove the insert that was placed in Slot B for shipment.

In the SG5660 enclosure, Slot B is the bottom slot. In the SG5612 enclosure, Slot B is the slot on
the right.

2.  Install the E5600SG controller into Slot B.

After you finish

Continue with cabling the appliance.

22 |  StorageGRID Webscale 10.4 Appliance Installation and Maintenance Guide

Содержание StorageGRID Webscale 10.4





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды