NetApp FAS9500 Скачать руководство пользователя страница 20

Страница: 20 / 84

-only-cfo-aggregates true

command.

◦

If the command fails because of a failed disk, physically disengage the failed disk, but leave the disk in
the slot until a replacement is received.

◦

If the command fails because of an open CIFS session, check with the customer how to close out CIFS
sessions.

Terminating CIFS can cause loss of data.

◦

If the command fails because the partner "not ready", wait 5 minutes for the NVRAMs to synchronize.

◦

If the command fails because of an NDMP, SnapMirror, or SnapVault process, disable the process. See
the appropriate content for more information.

11. Once the giveback completes, check the failover and giveback status with the

storage failover show

and storage failover show-giveback commands.

Only the CFO aggregates (root aggregate and CFO style data aggregates) will be shown.

12. If you are running ONTAP 9.6 or later, run the security key-manager onboard sync:

a. Run the

security key-manager onboard sync

command and then enter the passphrase when

prompted.

b. Enter the

security key-manager key-query

command to see a detailed view of all keys stored

in the onboard key manager and verify that the

Restored

column =

yes/true

for all authentication

keys.

If the

Restored

column = anything other than

yes/true

, contact Customer Support.

c. Wait 10 minutes for the key to synchronize across the cluster.

13. Move the console cable to the partner node.

14. Give back the target node using the

storage failover giveback -fromnode local

command.

15. Check the giveback status, three minutes after it reports complete, using the

storage failover show

command.

If giveback is not complete after 20 minutes, contact Customer Support.

16. At the clustershell prompt, enter the

net int show -is-home false

command to list the logical

interfaces that are not on their home node and port.

If any interfaces are listed as

false

, revert those interfaces back to their home port using the

net int

revert

command.

17. Move the console cable to the target node and run the

version -v

command to check the ONTAP

versions.

18. Restore automatic giveback if you disabled it by using the

storage failover modify -node local

-auto-giveback true

command.

Restore NSE/NVE on systems running ONTAP 9.6 and later

1. Connect the console cable to the target node.

Содержание FAS9500





















































































Результаты поиска

Содержание FAS9500

Отзывы:

Бренды по названию

Популярные бренды

NetApp FAS9500, Руководство пользователя

Результаты поиска

Содержание FAS9500

Отзывы:

Бренды по названию

Популярные бренды