NetApp FAS2600 Скачать руководство пользователя страница 686 | Manualshive

Страница: 686 / 786

background image

Video two of two: Performing end-to-end software configuration

The following video shows end-to-end software configuration for systems running ONTAP 9.6 and later.

Detailed steps - FAS9500

This article gives detailed step-by-step instructions for installing a typical NetApp system.
Use this article if you want more detailed installation instructions.

Step 1: Prepare for installation

To install your system, you need to create an account on the NetApp Support Site, register your system, and
get license keys. You also need to inventory the appropriate number and type of cables for your system and
collect specific network information.

You need to have access to the

NetApp Hardware Universe

for information about site requirements as well as

additional information on your configured system.

What you need

You might also want to have access to the

ONTAP 9 Release Notes

for your version of ONTAP for more

information about this system.

You need to provide the following at your site:

• Rack space for the storage system

• Phillips #2 screwdriver

• Additional networking cables to connect your system to your network switch and laptop or console with a

Web browser

Steps

684

«
...
684
685
686
687
688
...
»

Содержание FAS2600



















































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для FAS2600

Бренд: Garmin Страницы: 10

Бренд: Teac Страницы: 3

Бренд: Champion Страницы: 46

Бренд: Samsung Страницы: 42

Бренд: Boss Страницы: 5

Бренд: Sony Страницы: 46

Бренд: Sony Страницы: 42

Бренд: Sony Страницы: 40

Бренд: Sony Страницы: 42

Бренд: Sony Страницы: 46

Бренд: Sony Страницы: 44

HCD-EP313 - Personal Component System

Бренд: Sony Страницы: 44

Бренд: Sony Страницы: 44

Бренд: Sony Страницы: 48

HCD-EP707 - Micro Hi-fi Component System

Бренд: Sony Страницы: 56

Бренд: Sony Страницы: 52

HCD-ED2 - Compact Disc Deck Receiver

Бренд: Sony Страницы: 52

Бренд: Sony Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды