manualshive.com logo in svg

NetApp 42U 1280 mm System Cabinet, Руководство пользователя

Поделиться
Скачать
NetApp 42U 1280 mm System Cabinet Скачать руководство пользователя страница 6

Required tools and equipment

Before unpacking and installing on your system cabinet, you should gather the necessary tools and
equipment to move the system cabinet into place and install it or to perform maintenance on it.

•

The appropriate hardware guide for your disk shelves

•

The appropriate installation and setup instructions for your system

NetApp All Flash FAS Resources
NetApp FAS Storage Systems Resources
NetApp E-Series Systems Documentation Center

•

#1 and #2 Phillips screwdrivers

•

Torx driver for system cabinet screws

•

Leveling tool for leveling the system cabinet

Space requirements and system cabinet dimensions

When unpacking your system cabinet, you must make sure that you have enough room to remove the
system cabinet from the packing material. Also make sure that the intended location for the system
cabinet is large enough for you to move the cabinet into place.

Required space for unpacking the system cabinet

The following table defines the requires space needed to unpack and install your system cabinet:

Dimensions

U.S.

Metric

Shipping ramp length

80 in.

203.2 cm

Clearance beyond the ramp for
cabinet mobility

72 in.

182.9 cm

Shipping pallet depth

59 in.

149.9 cm

Shipping pallet width

42 in.

106.6 cm

Shipping pallet and packaging
height

86 in.

218.4 cm

Total rack space, 42U

73.5 in.

186.7 cm

Rail load capacity

Supports all current systems

Supports all current systems

Empty weight

~400 lbs (~181 kg) lbs

~ 181 kg

Fully loaded ship weight

Up to 1,800 lbs

Up to 816.5 kg

Fully loaded static weight

Up to 2,700 lbs

Up to 1,224.7 kg

Front service clearance

47.2 in.

120 cm

Rear service clearance

Note: 

The rear door is split.

Actual minimum rear
clearance is approximately
1/2 the recommendation.

30 in.

76.3 cm

6 | 42U 1280 mm System Cabinet Guide

Содержание 42U 1280 mm System Cabinet




































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды