Battery voltage, V
........................
.............................
..
.
................................................................................................................
...
.....................................3
Operation temperature range, °С
............................................
..........
..................................................................................................
.
.......
from
0
to
+40
Degree of enclosure protection
.........................................................................................................................................................
...
............
.
...........
IP
4
0
Operating frequency range, MHz
......................................................................................................................................................
.
..... 433,05...434,79
Maximum power of emitted signal,not more than, mW
...
.
..........
...............................................................................................
.....................................10
Number of control channels
................................................
.
.......................................................................................
...
...............................
...........
...........1
Battery type
.........
.
..........................................
..................
..............................................................................................................
...
.....................
CR 2032
Overall dimensions, mm
................................
.
............................................
.....
....................................................................................
...
.............43
×
30
×
10
1
1
One-channel Remote Control Radio 8101-1M is designed to control remotely the executive devices
of the Radio series, as well as executive devices of the Nero series (only with static code) using
transcoder Nero 8361 UPM.
One-channel Remote Control
Radio 8101-1M
Passport
1
.
Device description
1.1. Purpose
1.2. Specifications
1.3.Peculiarities
- pocket-sized device;
-
step-by-step control («UP-STOP-DOWN-STOP…» commands are executed circle-wise);
-
transmission of control commands with static or dynamic code.
Factory setting – dynamic code.
When controlling the executive device in static mode, the remote control signal may be copied by an attacker, thus allowing him to control
your object (roller shutter, barrier, gate). In dynamic mode, there's no possibility to copy and hack the device. Dynamic transmission of
the radio remote control is supported only by devices released after year 2015. For more information see User Manual, apply to manager
or to the technical support service, the telephone number of which you can find on the manufacturer's website.
2. Programming
Action
Indication
Recording the remote control channel into the memory of the executive device
1. Start the programming mode in the executive device (see Manual
for the corresponding device).
b) with static code: briefly press the remote control button.
2. Record the remote control:
a) with dynamic code: press the remote
control button and hold it
for more than 2 seconds.
Confirmation of record on the executive device depends on type of the
device and programming mode: short-long-short green flash on the
indicator or long-term movement «DOWN», short-term «UP-DOWN»
movement and long-term «UP» movement of the roller shutter.
If the remote control is not recorded, it means that the executive device supports only the static transmission code. Please change
operation mode to the static one.
Changing the remote control code: selection of dynamic or static code
1. Press the remote control button 4 times in a row, then press one
more time and hold for more than 4 sec.
Pressing interval should be not more than 1 sec.
2. To change the operation mode press the remote control button
and hold for more than 1 sec.
Radio codes are switched circle-wise
every time you press the remote control button.
2. The indicator blinks:
- single flash — static code;
1. After the last pressing, the indicator blinks off and starts blinking
with an interval of 1 sec.
- double flash — dynamic code (factory operation mode);
- triple flash — dynamic code with high range.
Delete the remote control from the memory of the executive device
1. Start the programming mode in the executive device (see Manual
for the corresponding device).
a) Delete the remote control in dynamic mode:
1) start the programming mode (press remote control button 3
times in a row, then press it one more time and hold for more than
4 sec. Pressing interval should be not more than 1sec.);
b) Delete the remote control in static mode: press the remote
control button and hold for more than 1 sec.
2) press the remote control button and hold for more than 1 sec.
Indication on the executive devices is the same for both modes
(depends on type of the device and programming mode): one long-
term red flash or long-term
«
DOWN-UP
»
movement of the roller
shutter.
b) Remote control indicator lights steadily.
a) After the last pressing, the indicator starts blinking quickly;
Attention! If the static operating mode was previously enabled on the remote control, then when entering the programming
mode, the remote control will automatically change the static operating mode to the dynamic one.
The remote control will exit the programming mode after 16 seconds of inactivity.
