December 2004 4
16025861
©2004 Maytag Services
f
o
e
g
a
t
S
e
l
c
y
C
h
s
a
W
o
T
s
e
c
n
a
v
d
A
k
a
o
s
e
r
P
k
a
o
s
e
r
P
f
o
d
n
E
h
s
a
W
f
o
s
e
t
u
n
i
M
5
y
r
e
v
E
e
m
i
T
h
s
a
W
n
i
a
r
D
/
n
i
p
S
e
h
T
f
o
p
e
t
S
y
r
e
v
E
e
li
f
o
r
P
n
i
p
S
e
s
n
i
R
e
s
n
i
R
f
o
d
n
E
e
g
n
a
R
d
e
e
p
S
d
e
y
a
l
p
s
i
D
m
p
r
9
9
-
0
)
a
)l
a
u
t
c
a
(
9
9
-
0
m
p
r
9
9
9
-
0
0
1
)
b
0
1
/
d
e
e
p
S
Q
uick Service Cycle
While in service mode, pressing the
delicates
key
will start a quick service cycle. This will be a quick
check of all systems.
The following steps will be followed.
1. Energize the cold and bleach water valves. Fill to
Low level, then turn bleach and cold off.
2. Energize the hot and fabric softener water valves. Fill
to high level, then turn all valves off.
3. Lock the door.
4. Tumble using 7/3 tumble pattern for 12 sec.
5. Turn the drain on.
6. Spin to 800 RPM using default rates.
7. End spin and coast down.
8. Unlock the door when the RPM is zero.
9. Display a ‘PA’ (Passed) on continuously for 10 sec-
onds if no diagnostic codes were logged during this
test.
The up arrow if pressed will advance to the next step.
The right most dot will be turned on as an indication
of failure and stay on until quick service cycle test
has reached the end. Any diagnostic code logged
during this test will result in failure of the test, but will
not necessarily stop the test. While in quick service
cycle, the pressing of the
hand wash
will suspend
the machine at this step for 30 minutes until the
Hand Wash key is pressed again. All LED’s will
flash on and off while the cycle is suspended, or on
hold.
Motor Drive System
To check the system, check the board for proper
output to the motor control. Performing a board
output test does this. Then perform the Motor
Control Board Output Test.
Motor Control Board Output Test
1. Disconnect power to the washer.
2. Remove the front panel and pull the JP4 Connector
from the motor control board.
The following Quick Spin test steps are as follows:
1) Lock the door.
2) Spin to 350 rpm and hold for 6 seconds.
3) Spin to 550 rpm and hold for 6 seconds.
4) Spin to 600 rpm and hold for 6 seconds.
5) Spin to 650 rpm and hold for 6 seconds.
6) Spin to 800 rpm and hold for 6 seconds.
If the
Spin
key is pressed again during the Quick Spin
test, the current speed will be held indefinitely. Press-
ing the
Spin
key again will allow the quick test to
proceed as listed above.
When the washer is in the Service Mode, the speed
will be displayed as a two digit number or a letter/
number.
Quick Spin Test
While in service mode, the pressing of
spin
key shall
start the washer in the
quick spin
mode.
3. Reconnect the washer power cord to supply
voltage. Make sure the door is closed.
4. Press
delicates
and
heavy soil
keys for 3 sec-
onds to activate Service Mode.
!
WARNING
To avoid risk of electrical shock, personal injury, or death, disconnect power to washer before servicing,
unless testing requires it.
Troubleshooting
