Neoway N720 страница 61 Скачать руководство пользователя

Страница: 61 / 94

N720 OpenLinux

Hardware User Guide

(dhrd)

Data hold time

1.5

t(dsurd)

Data set-up time

1.65

t(pddwr)

Delay time from data write to
transmit

2.5

6.15

t(pdcwr)

Delay time from command write to
transmit

-7.85

2.65

3.4.3 Bluetooth

Signal

Pin

I/O

Function

Remarks

BT_WAKEUP_HOST

Bluetooth wakeup host

Multiplex CTS and
RTS of UART5

BT_WAKEUP_SLAVE 52

Bluetooth wakeup slave

BT_UART_TXD

Data TX of Bluetooth UART

Used for Bluetooth
data transmission.
Leave them floating if
they are not used.

BT_UART_RXD

Data RX of Bluetooth UART

BT_UART_CTS

Clear to send

BT_UART_RTS

Request to send

BT_EN

Bluetooth enable

Leave this pin floating
if it is not used.

BT_PWR_EN

Control of Bluetooth external
power

Leave this pin floating
if it is not used.

N720 OpenLinux communicates with Bluetooth chipset through UART for data transmission. To use
Bluetooth audio, connect one set of PCM signals (pins 65 to 68). See section 3.7 MUX Interfaces.
Figure 3-45 shows the Bluetooth connection.

Содержание N720































































































Результаты поиска

Содержание N720

Отзывы:

Похожие инструкции для N720

Бренды по названию

Популярные бренды

Neoway N720, Руководство пользователя по оборудованию

Результаты поиска

Содержание N720

Отзывы:

Похожие инструкции для N720

Бренды по названию

Популярные бренды