Neousys Nuvo-7160GC Series Скачать руководство пользователя страница 33

Страница: 33 / 159

Nuvo-7160GC/ Nuvo-7164GC Series

2.4

Rear Panel I/O

Nuvo-7160GC rear panel features

MezIO

port,

four (4) COM ports

, 3-pin terminal and 3-pin on/ off

control. The Cassette module can be located at the bottom of the enclosure and there are two reserved

openings for D-sub9 connectors. The connectors of the installed PCI/ PCIe or graphics card within the

Cassette module can be accessed from this side of the panel.

No.

Item

Description

MezIO

I/O

Reserved for MezIO

I/O connector. Connector may vary

depending on your choice of MezIO

4-Pole 3.5mm

headphone/

microphone jack

The 4-pole 3.5mm jack accepts microphone voice input and

headphone speaker sound output.

COM ports 1-4

The four COM ports offer communication with external devices.

3-pin terminal

block (DC/

ignition input)

Compatible with DC power input from 8~35V, the terminal block

is also used for ignition signal input.

3-pin Remote

on/ off control

Allows for external switch extension when the system is placed

inside a cabinet.

Area

green

Cassette

module

The cassette module offers a separate compartment to manage

thermal conditions and reduce installation complications of an

add-on card.

Area

in red

Reserved port

opening/ cover

The area indicated in red on the rear panel of Nuvo-7160GC

series feature reserved port opening/ cover for additional D-sub 9

connectors.

Содержание Nuvo-7160GC Series
































































































































































Результаты поиска

Содержание Nuvo-7160GC Series

Отзывы:

Бренды по названию

Популярные бренды

Neousys Nuvo-7160GC Series, Руководство пользователя

Результаты поиска

Содержание Nuvo-7160GC Series

Отзывы:

Бренды по названию

Популярные бренды