Neousys Technology POC-351VTC Скачать руководство пользователя страница 25

POC-351VTC 

25 

2.2.5 

System Status LED 

 

There are four LED indicators on the front panel: PWR, HDD, WDT and IGN. The 

descriptions of these four LEDs are listed in the following table. 

Indicator 

Color 

Description 

PWR 

Green 

Power indicator, lid when system is on 

HDD 

Red 

Hard drive indicator, flashing when SATA HDD is active 

WDT 

Yellow 

Watchdog timer indicator, flashing when watchdog timer has started 

IGN 

Green 

Ignition power control, lid when IGN signal is applied. 

2.2.6 

DVI-I Port 

 

The system features a DVI-I connector on its front panel that is also compatible with 

VGA signals. The DVI and VGA outputs are directly driven by integrated Intel HD 

graphics engine and support up to 1920 x 1200 resolution. 

For VGA monitor, Neousys offers a specialized DVI-to-VGA adapter as an accessory 

shipped with the system. This adapter supports VGA DDC signals and thus 

eliminates compatibility issues with VGA monitors. Or you can use a DVI-I to 

VGA+DVI-D Y-cable to support two independent display outputs 

 

 

DVI to VGA adapter 

Optional DVI to VGA+DVI Y-cable 

Содержание POC-351VTC



































































Отзывы: