Neousys Technology Nuvo-8208GC Series Скачать руководство пользователя страница 128

Страница: 128 / 141

Nuvo-8208GC

128

5.4

Intel

Optane

Memory BIOS Setup and Driver

Installation

The system is compatible with Intel

Rapid Storage Technology that supports the installation

of Intel

Optane

memory to significantly boost traditional hard disk drive read and write

performances. Intel® Optane

memory is Intel® RST’s latest system acceleration solution

featuring a dual-media/disk combination (ultrafast media for file and block c slow

media for storage capacity) that is presented to the host OS as a single SSD. The ultrafast

media utilizes PCIe NVMe SSDs that are based on Intel® Optane

technology with read

speed of up to 3000Mb/ sec and write speed of up to 2000Mb/ sec.

To setup Intel

Optane

memory, please perform the following steps:

Press the power button to startup your system (please restart if your system is already

up and running) and press F2 to enter BIOS.

Go to “Advanced > SATA And RST Configuration”.

Содержание Nuvo-8208GC Series














































































































































Результаты поиска

Содержание Nuvo-8208GC Series

Отзывы:

Neousys Technology Nuvo-8208GC Series, Руководство пользователя, Страница: 128 / 141

Результаты поиска

Содержание Nuvo-8208GC Series

Отзывы: