Neousys Technology Nuvo-3000 Series Скачать руководство пользователя страница 79

Страница: 79 / 101

Nuvo-3000 Series User’s Manual

Page 79 of

101

4.1.3 Power On after Power Failure Option

This option defines the behavior of Nuvo-3000 when DC power is supplied.

Value

Description

S0 – Power On

System is powered on when DC power is supplied.

S5 – Power Off

System is kept in off state when DC power is supplied.

Last State

The on/off state of the system is determined according to the last state

when DC power is disconnected. For example, if system is still on but

DC power is unplugged, the system is powered on next time when DC

power is supplied.

To set “Power On after Power Failure” option:

1. When Nuvo-3000 boots up, press F2 to enter BIOS setup utility.

2. Go to

[Advanced]

[Chipset Configuration]

3. Set the

[Power On after Power Failure]

to a proper value for your Nuvo-3000.

4.1.4 Wake-on-LAN Option

Wake-on-LAN (WOL) is a mechanism which allows you to turn on your Nuvo-3000 via

Ethernet connection. To utilize Wake-on-LAN function, you have to enable this option first in

BIOS settings. Please refer to section 3.7.3 for instructions of using WOL function.

To enable/disable “Wake on LAN” option:

1. When Nuvo-3000 boots up, press F2 to enter BIOS setup utility.

2. Go to

[Power]

Содержание Nuvo-3000 Series






























































































Результаты поиска

Содержание Nuvo-3000 Series

Отзывы:

Похожие инструкции для Nuvo-3000 Series

Бренды по названию

Популярные бренды

Neousys Technology Nuvo-3000 Series, Руководство пользователя

Результаты поиска

Содержание Nuvo-3000 Series

Отзывы:

Похожие инструкции для Nuvo-3000 Series

Бренды по названию

Популярные бренды