Neopost MaxiMailer HD Скачать руководство пользователя страница 32

Страница: 32 / 69

MaxiMailer HD Operator Manual

5.9.4 setting

the feed

options for the

feed unit

Press the lower icon of the numbered feed unit (showing the unit icon),
and the following dialog box appears:

address Carrier:

Select whether or not this is the address document

(this will normally be the DTI).

note:

this can also be selected

from ‘Miscellaneous’ (see page

37). Whichever is set the later takes

precedence.

feed Control Mode:

Options are: Off / Feed Always / OMR or Barcode

Select (the latter only available if unit is OMR/Barcode enabled).

see

OMR/Barcode User’s Manual for defining barcode setups. Note:

OMR or barcode reading are optional features.

flip mode (DTI only):

Options are Flip / No-flip. Select no-flip if form

is required to feed straight through without turnover.

fold Mode (not applicable to DTI):

(Tower folder only) Options are:

Singly / Together / Via accumulator (the latter is only available if the

unit has an accumulator fitted: if so, forms will group in accumulator

first before folding.only).

form Count (not applicable to DTI):

Only available if ‘Mark reading’

is Off. If multiple forms are required, set this to the required quantity.

note:

ensure that the maximum fold capacity is not exceeded.

Reader (Head) ID:

Only available if ‘Mark reading’ is On. Options are

Reader (Head) 1 / Reader (Head) 2 / Both readers. Only available if

two read heads are fitted.

Mark Reading:

Only available if unit is OMR/Barcode and a marked

document is selected. Options are: Off / OMR marks / Barcode labels /

2D Datamatrix / OCR.

Note that the options

in the dialog box may

vary from those shown,

depending on whether the

unit is a feeder or a folder.

Select ‘Save as Default’

to make this the default

for all new setups. These

settings then apply to ‘Load

Default’

Содержание MaxiMailer HD






































































Результаты поиска

Содержание MaxiMailer HD

Отзывы:

Похожие инструкции для MaxiMailer HD

Бренды по названию

Популярные бренды

Neopost MaxiMailer HD, Руководство оператора

Результаты поиска

Содержание MaxiMailer HD

Отзывы:

Похожие инструкции для MaxiMailer HD

Бренды по названию

Популярные бренды