NeoDen K1830 Скачать руководство пользователя

Страница: 43 / 52

slot rather than that of component.

(3) Due to peel strength or installation issue of wasted film, the film on tape won’t be peeled

completely

(4)The nozzle was blocked

(5) The nozzle is damaged or has a crack

(6) The size issue of nozzle would cause air leakage or insufficient suction.

(7) The air hose is blocked or has a leakage problem, and even the pump has an issue.

●Frequently throwing components. Some suggestions are listed below,

(1) Up-looking camera can’t take a clear picture of component due to brightness issue for example.

(2) The pins are distorted

(3) The size or shape isn’t aligned with that in “Footprint library’’

(4) The size of nozzle is inappropriate or insufficient suction. (5) The nozzle has solder paste or rubbish cause air

leakage

(6) The nozzle is damaged or cracked cause air leakage

10.4 Continuous SMT production

Follow the SOP to start production

Notes:

(1) Do not touch the surface to board to avoid damaging the printed solder paste.

(2) When the error message occurs, please check out and solve it a.s.a.p.

(3) Once reloading the component during production, pay attention to the model, specification, polarity and direction of

components.

(4) Clear the reject box timely to avoid wasted materials stacked too high to damage the mount head

Zhejiang

NeoDen Technology Co.,Ltd.

Содержание K1830





















































Результаты поиска

Содержание K1830

Отзывы:

Похожие инструкции для K1830

Бренды по названию

Популярные бренды

NeoDen K1830, Руководство пользователя

Результаты поиска

Содержание K1830

Отзывы:

Похожие инструкции для K1830

Бренды по названию

Популярные бренды