background image

8

      WARNING

Before connecting a tool to a power source (mains switch power point receptacle, 

outlet, etc.) be sure that the voltage supply is the same as that specified on the nameplate of the tool.

 

A power source with a voltage greater than that specified for the tool can result in serious injury to the user, 

and damage to the tool. If in doubt, do not plug in the tool. Using a power source with a voltage less than the 

nameplate rating is harmful to the motor.

Mitre Saw Safety

       

WARNING!

•  Hold the power tool by insulated gripping surfaces only, when performing an operation where the cutting 

tool may contact its own cord. Contact with a “live” wire will also make exposed metal parts of the power 
tool “live” and could give the operator electric shock.

•  Always use blades with correct size and shape (diamond versus round) of arbour holes. Blades that do not 

match the mounting hardware of the saw will run eccentrically, causing loss of control.

•  Never use damaged or incorrect blade washers or bolt. The blade washers and bolt were specially 

designed for your saw, for optimum performance and safety of operation.

•  Adjust the cutting depth to the thickness of the workpiece. 
•  Keep hands away from cutting area and the blade.

IMPORTANT:

 If you are unsure about operating this tool after reading these instructions, please seek 

additional training.
a)  Do not allow anyone under the age of 18 years to operate this saw
b)  When operating the saw, use safety equipment including safety goggles or shield, ear protection, dust 

mask and protective clothing including safety gloves

c)  Power tools may produce vibration. Vibration can cause disease. Gloves may help to maintain good blood 

circulation in the fingers. Hand-held tools should not be used for long periods without a break

d)  Whenever possible, use a vacuum dust extraction system to control dust/waste
e)  Do not attempt to cut material thicker than detailed in the Specifications section of this manual
f)  Mitre saws are not designed for general cutting of firewood. Always ensure wood is dry with suitable flat 

surfaces, so it is securely held on the mitre table and fence

g)  Only guide the saw blade against the workpiece when the tool is switched on. Otherwise there is a risk of 

kickback when the blade becomes wedged in the workpiece

h)  Adjust the cutting depth to the thickness of the workpiece 
i)  Never remove dust, chips or waste by hand close to the blade. Ensure the tool is unpowered and use a 

suitable brush

j)  Only use saw blades recommended by the manufacturer that conform to EN 847-1 or equivalent standard 

in your country 

k)  Keep  rags, cloths and string away from the work area and ensure the operator’s clothing has no loose 

strands of material that could become caught in the rotating blade, causing injury. Gloves worn by the 
operator must not have loose strands

l)  Ensure the mitre saw is operated without risk of items stored above falling onto the tool. Vibration of the 

tool may cause nearby stored items to move

m) Keep saw blades not fitted to the tool in a suitable container to protect against cuts - especially when 

carrying

n)  Always ensure the saw blade is suitable for the material being cut and that the maximum rpm of the blade 

is not exceeded by the maximum no load speed of the saw

o)  When using blades with a larger bore than the mitre saw spindle ensure the correct size bore spacer 

(spindle ring) is used 

p)  When transporting the saw, ensure its own transport handle is used (not the operating handle) and that the 

saw is in the locked down position

q)  Do not remove cut-off material or swap the workpiece without first returning the saw head to the top 

position with the guard closed

r)  Ensure work is correctly supported. Large panels may sag under their own weight and bind the saw blade. 

Supports must be placed under the panel on both sides, close to the line of cut and near the edge of the 
panel

s)  Ensure all supports and power cables are completely clear of the cutting path
t)  Always secure the workpiece to a stable platform, ensuring body exposure is minimised, avoiding blade 

binding, or loss of control

u)  Do not stand in line with the saw blade of the mitre saw in use. Stand to the side to avoid possible 

kickback

v)  Note the direction of rotation of the motor and the blade

w) Inspect the workpiece and remove all nails and other embedded objects prior to starting work
x)  Do not apply any sideways or twisting force to the blade whilst cutting
y)  If a cut does not extend to the edge of the workpiece, or if the blade binds in the cut, allow the blade to 

come to a complete stop and lift the saw out of the workpiece

z)  Do not attempt to free a jammed blade before first disconnecting the machine from power
1.  Beware of projected waste. In some situations, waste material may be projected at speed from the cutting 

tool. It is the user’s responsibility to ensure that other people in the work area are protected from the 
possibility of projected waste

2.  If you are interrupted when operating the saw, complete the process and switch off before diverting your 

attention

3.  Check the lower guard for proper closing before each use. Do not operate the saw if the lower guard does 

not move freely and close instantly. Never clamp or tie the lower guard into the open position. If the saw is 
accidentally dropped, the lower guard may be bent. Raise the lower guard with the retracting handle and 
make sure it moves freely and does not touch the blade or any other part, in all angles and depths of cut

4.  Never operate the saw without the guards fitted
5.  Periodically check that all nuts, bolts and other fixings have not loosened, tighten where necessary
6.  Do not use blades of High Speed Steel (HSS blades).
7.  If the table insert is damaged or worn, have it replaced by a power tool repairer.

The tool must be used only for its prescribed purpose.

 

Any use other than those mentioned in this manual 

will be considered a case of misuse. The user, and not the manufacturer, shall be liable for any damage or 

injury resulting from such cases of misuse. The manufacturer shall not be liable for any modifications made to 

the tool nor for any damage resulting from such modifications. Even when the tool is used as prescribed it is 

not possible to eliminate all residual risk factors.

Laser Safety

The laser used in this device is a Class 2 laser with maximum power of ≤1mW and a wavelength of           
400-700nm. These lasers do not normally present an optical hazard, although staring at the beam may cause 
flash blindness. 

WARNING: Avoid direct eye contact. 

A hazard may exist if you deliberately stare into the beam, please observe all safety rules as follows:
•  The laser shall be used and maintained in accordance with the manufacturer’s instructions
•  Do not switch on the laser light until the tool is ready to cut
•  Never aim the beam at any person, and particularly not into the eyes of any person or animal, or any 

object other than the workpiece

•  Always ensure the laser beam is aimed at a sturdy workpiece without reflective surfaces. i.e. wood or 

rough-coated surfaces are acceptable. Reflective sheet steel or similar is not suitable for laser use as the 
reflective surface could direct the beam back at the operator

•  Do not change the laser light assembly. Repairs must only be carried out by the laser manufacturer or an 

authorised agent. 

Do NOT exchange with a different type of laser

CAUTION:

 Use of controls or adjustments or performance of procedures other than those specified herein may 

result in hazardous radiation exposure. 

Please refer to the relevant EN standards, EN60825-1/A1:2002 for more information on Lasers.

 

Product Familiarisation

1.  Dust Port
2.  Left Safety Lock-Off
3.  Right Safety Lock-Off
4.  Operating Handle
5.  Release Lever
6.  Brush Access Cover 
7.  Motor Vents
8.  Rotation Indicator
9.  Spindle Lock
10.  Saw Blade
11.  Rotating Blade Guard
12.  Blade Channel
13.  Throat Plate

14.  Throat Plate Screw
15.  Mitre Table Locking Knob
16.  Click-Stop Lever
17.  Bevel Angle Lock
18.  Mitre Angle Indicator 
19.  Mitre Angle Indicator Screw
20.  Mitre Angle Gauge
21.  Mitre Table
22.  Fence
23.  Bench Mounting Hole
24.  Workpiece Support Knob
25.  Workpiece Support
26.  Workpiece Support Stop

27.  Clamp Base
28.  Fixed Table
29.  Small Fence
30.  Clamp
31.  45° Left Bevel Bolt
32.  45° Left Bevel Locking Nut
33.  Dust Bag
34.  Sliding Bar
35.  Slide Lock
36.  Clamp Arm Knob
37.  Small Fence Knob
38.  Fence Bolt
39.  Clamp Mounting Knob

Содержание CT1503













Отзывы: